Need help?Do you have a question about the Xtant 301A and is the answer not in the manual?
General| THD at Rated Power | 0.05% |
|---|---|
| Crossover Slope | 12dB/octave |
| THD | 0.05% |
| Signal to Noise Ratio | >100dB |
| Damping Factor | 200 |
| Crossover Frequency | 50Hz - 250Hz |
| Bass Boost | 0dB - 18dB |
| Power Output | 300W |
Xtant values customer feedback and incorporates it into product development.
Ensuring product compatibility with a wide variety of third-party audio components.
Focus on providing the finest mobile audio components through critical evaluation.
Chosen for passion and expertise, recommending professional installation.
High-powered audio systems can cause hearing damage or traffic hazards; use lower volumes while driving.
Assists professional installers with critical installation techniques for high-performance systems.
Specifies minimum wire gauge requirements for power, ground, and speaker cables.
Recommends a 50 amp fuse for the 301a and in-line at the battery for safety.
Advise to install amplifiers and accessories in a location free from moisture or water exposure.
Employs cooling for thermal management with an on-board thermal sensing circuit regulating fan speed.
Features a fully regulated, Pulse Width Modulated power supply for consistent output performance.
Eliminates system noise from ground-loops and increases input sensitivity for wider head unit compatibility.
Three ports allow docking of signal processing modules for system expansion and customization.
Allows the amplifier to produce maximum power (300 Watts) into 4 or 2 ohm speaker loads.
Incorporates Thermal and Overcurrent protection to maintain operation during issues.
Three LEDs indicate operational status: ON (red), overcurrent (yellow), and thermal protection (orange).
The amplifier's frequency response range is 5 Hz to 50 kHz +/- 3 dB.
Delivers 300 Watts per channel into both 4-ohm and 2-ohm loads.
Total Harmonic Distortion is specified as less than 0.04%.
The signal to noise ratio is greater than 100 dB.
Accepts unbalanced sources from 100 mV to 8.5 V RMS and balanced sources from 100 mV to 17 V RMS.
Includes a CM12LP Crossover module.
Features 2 ports for amplifier modules and 1 port for line outputs.
Designed to operate within an 11 to 15 Volts range.
Requires a 50 Amp fuse for proper operation and safety.
The product comes with a Limited 4 Year Parts and Labor warranty.
The 301a has three accessory ports: two for amplifier modules and one for RCA line outputs.
Modules are designed for horizontal or vertical mounting, fitting specific port types.
Ports allow adding signal processing like band pass filters or EQ/crossover modules.
The Line Out port accepts vertical modules for bass equalization or crossover functions.
A precision tuning instrument for adjustable one-band parametric equalization, frequency, Q, and gain.
A 24 dB per octave Linkwitz-Riley crossover filter to improve loudspeaker response and design flexibility.
12 dB per octave Butterworth filter networks for High-Pass (CM12H) or Low-Pass (CM12L) functions.
Modules activate passive speaker terminals, providing attenuation levels of 4, 8, 12, or 16 dB.
Periodic cleaning of fan and circuit board recommended every 30-90 days to prevent dust buildup.
Check fan for obstructions if amplifier overheats; thermal protection may engage, reducing power.
Use low-pressure air to blow off dust; do NOT use high-pressure sources or brushes on the circuit board.
Clean the stainless steel cover with a cotton cloth, optionally using WD-40 for thorough cleaning.
Customer satisfaction is the primary purpose, focusing on trust, respect, and minimizing downtime.
Contact Customer Service for technical assistance and product/installation information from 8:00 am to 5:00 pm MST.
Provides phone, fax, and USA toll-free numbers for Xtant's Customer Service Department.
Covers defects in materials/workmanship for 4 years (electronics) / 3 years (speakers) when installed by an Authorized Dealer.
Products installed by non-authorized dealers carry a limited one (1) year parts and labor warranty.
Requires original sales receipt and proof of authorized dealer installation for warranty claims.
Excludes units with removed serial numbers, altered units, misuse, neglect, or accidents.
Limits liability for incidental, consequential, or commercial damages; implied warranties are limited to this duration.
Contact Authorized Dealer for service; obtain Return Authorization Number for out-of-warranty returns.
Record owner's name, vehicle make/model, year, and amplifier serial number.
Log input sensitivity jumper settings and output gain adjustment positions.
Document which amplifier and RCA line output accessory modules were installed.
Record the Xtant Select Dealer, installation specialist, and date of installation.
To Next Page
