Yaesu FT-2000 - MENU MODE LIST User Manual

Page 108 FT-2000 OPERATING MANUAL
MENU MODE
The Menu system of the FT-2000 provides extensive customization capability, so you can set up your transceiver just the
way you want to operate it. The Menu items are grouped by general utilization category, and are numbered from “
001 AGc001 AGc
001 AGc001 AGc
001 AGc
FST DLYFST DLY
FST DLYFST DLY
FST DLY” to “
149 tGEn EMRGNCY149 tGEn EMRGNCY
149 tGEn EMRGNCY149 tGEn EMRGNCY
149 tGEn EMRGNCY.”
USING THE MENU
1. Press the
[
MENU
]
button momentarily, to engage the
Menu mode.
The Main (VFO-A) frequency display will show the
Menu Number and Menu Group name, while the Sub
(VFO-B) frequency display will show the Menu item;
the Multi-Display window shows the current setting of
the currently-selected Menu item.
2. Rotate the Main Tuning Dial knob to select the Menu
item you wish to work on.
3. Rotate the
[
SUB VFO-B
]
knob to change the current
setting of the selected Menu item.
ADVICE:
Press the
[
CLEAR
]
button momentarily to reset the
selected Menu item to the factory default value.
4. When you have finished making your adjustments,
press and hold in the
[
MENU
]
button for two seconds
to save the new setting and exit to normal operation. If
you only momentarily press the
[
MENU
]
button, the
new settings will not be retained.
Main Tuning Dial Knob
[
SUB VFO-B
]
Knob
[
MENU
]
Button
Menu Mode Reset
You may reset all the Menu settings to their original factory defaults, if desired.
1. Turn the front panel
[
POWER
]
switch off.
2. Press and hold in the
[
MENU
]
button, and while holding it in, press the
[
POWER
]
switch to turn the transceiver
back on. Now release the
[
MENU
]
button.
Menu Number Menu Group Name Menu Item
Menu Setting
[
CLEAR
]
Button

Yaesu FT-2000 - MENU MODE LIST Specifications

General

Brand	Yaesu
Model	FT-2000 - MENU MODE LIST
Category	Transceiver
Language	English

Summary

Using the FT-2000 Menu Mode

How to Use the Menu System

Step-by-step guide on navigating and adjusting menu items using buttons and dials.

Menu Mode Reset Procedure

Instructions to reset all menu settings to factory defaults by powering off and on.

FT-2000 AGC Menu Settings

AGC FAST Delay and Hang Time

Sets delay and hang time for the AGC FAST mode receiver.

AGC MID Delay and Hang Time

Sets delay and hang time for the AGC MID mode receiver.

AGC SLOW Delay and Hang Time

Sets delay and hang time for the AGC SLOW mode receiver.

FT-2000 Display Menu Settings

Display Color and Brightness

Configure display color, meter, and VFD brightness levels.

Tuning Offset Indicator Settings

Select parameters for the Tuning Offset Indicator.

Sub-band S-meter Peak Hold

Set the peak hold time for the Sub (VFO-B) receiver's S-meter.

Rotator Indicator Configuration

Set starting point and adjust rotator controller indicator needle.

Spectrum Scope Display Options

Enable/disable QMB Marker and Sub band frequency display.

FT-2000 Keyer Menu Settings

Beacon and Contest Number Settings

Configure beacon interval and contest number format/initial value.

CW Message Memory Entry

Permits entry of CW messages for message registers 1 and 2.

FT-2000 General Menu Settings

Antenna Selection and Beep Level

Set antenna selection method and beep level.

CAT Interface Configuration

Configure CAT baud rate, time-out timer, and RTS/Data LED.

Memory Group and Quick Split

Enable Memory Group Operation and set Quick Split tuning offset.

FT-2000 Mode-CW Menu Settings

CW Keyer Operation and Wiring

Select keyer mode (OFF, bug, ELE, ACS) and paddle wiring.

CW Keying on SSB and BFO

Enable CW keying during SSB and set CW BFO injection side.

CW Break-in and Waveform

Set CW break-in mode (Semi/Full) and waveform shape.

CW Dot-Dash Ratio

Adjusts the Dot:Dash ratio for the electronic keyer.

FT-2000 Mode-DAT Menu Settings

Data Input Path and Gain

Select data input path and set data input level from TNC.

Data Output and VOX Settings

Configure data output receiver, level, and VOX delay/gain.

Packet Frequency Display and Offset

Set packet frequency display offset and carrier point.

FT-2000 Mode-FM Menu Settings

FM Microphone Settings

Set microphone gain and select microphone for FM mode.

FM Repeater Shift Settings

Set repeater shift magnitude for 28 MHz and 50 MHz bands.

FT-2000 Mode-RTTY Menu Settings

RTTY Polarity and Output Settings

Select RTTY receive/transmit polarity and output receiver/level.

RTTY Shift and Tone

Set frequency shift and mark tone for FSK RTTY operation.

FT-2000 RX Audio Menu Settings

AGC Amplifier Gain Curve

Selects the gain curve of the AGC amplifier.

Headphone Mixing Modes

Selects audio mixing modes for dual receive headphones.

FT-2000 RX DSP Menu Settings

Contour Filter Gain and Q-Factor

Adjusts gain and Q-factor of the Contour filter.

DSP Filter Characteristics (CW)

Selects passband characteristics and shape for CW DSP filter.

DSP Filter Passband (CW Narrow)

Selects the passband for the CW 'Narrow' DSP filter.

DSP Filter Characteristics (PKT/RTTY)

Selects passband characteristics and shape for PKT/RTTY DSP filters.

DSP Filter Passband (PKT/RTTY Narrow)

Selects the passband for PKT/RTTY 'Narrow' DSP filters.

DSP Filter Characteristics (SSB)

Selects passband characteristics and shape for SSB DSP filters.

DSP Filter Passband (SSB Narrow)

Selects the passband for the 'Narrow' SSB DSP filter.

FT-2000 Scope Menu Settings

Spectrum Scope Scan Start Frequencies

Sets scan start frequency for FIX mode Spectrum Scope on various bands.

FT-2000 Tuning Menu Settings

Tuning Dial Speed and Fine Tuning

Set tuning dial speed and enable/disable CW fine tuning.

Tuning Steps for MHz Select and AM/FM

Configure tuning steps for MHz Select and UP/DWN keys.

Tuning Dial Speed for FM and Band Skipping

Set FM dial speed and program skipped bands.

FT-2000 DVS Menu Settings

Voice Memory Audio Levels

Set audio output level for voice memory and mic input level.

FT-2000 Mode-SSB Menu Settings

SSB Microphone Selection

Selects the microphone to be used on the SSB modes.

SSB Transmitter Bandpass Filter

Selects the audio passband of the DSP modulator on SSB mode.

SSB Carrier Point Adjustment

Adjusts receiver carrier point for Main/Sub LSB and USB modes.

FT-2000 TX Audio Menu Settings

Parametric EQ Low Range Settings

Set center frequency, gain, and Q-factor for low range EQ.

Parametric EQ Middle Range Settings

Set center frequency, gain, and Q-factor for middle range EQ.

Parametric EQ High Range Settings

Set center frequency, gain, and Q-factor for high range EQ.

Speech Processor EQ Low Range Settings

Set center frequency, gain, and Q-factor for SP low range EQ.

FT-2000 TX General Menu Settings

Maximum Output Power and RF PWR Control

Set max output power limit and configure RF PWR knob.

TX GND and Tuning Power Settings

Enable/disable TX GND jack and set tuning power for linear amps.

VOX Audio Source and Emergency Channel

Select VOX audio source and enable Alaska Emergency Channel.