Why is my Yamaha 85AET Outboard Motor gauge operating unstably?
If the gauge operates unstably, it's likely that the resistor isn't connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs to resolve this.
Why Yamaha Outboard Motor PTT unit does not hold the outboard motor up?
If your Yamaha Outboard Motor's PTT unit isn't holding the motor up, a possible cause is that the manual valve is opened; check the manual valve. Also, there might not be enough PTT fluid, so ensure you add sufficient fluid. Another reason could be PTT fluid leakage; in this case, check the PTT unit for leakage. Finally, the main valves might not be operating, requiring you to disassemble and inspect the PTT unit.
What to do if the Yamaha 85AET gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
Why is the Yamaha Outboard Motor gauge response poor?
If the gauge response is poor, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Replace the faulty unit or remove the heavy signal output unit.
Why doesn't my Yamaha 85AET Outboard Motor boat speed gauge show?
If the boat speed and/or coolant pressure gauge isn't showing, it means the optional sensor hasn't been installed. Install the optional sensor to fix this.
What to do if my Yamaha Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or replace the gauge itself.
Why is the illumination not lighting on my Yamaha 85AET gauge?
If the illumination isn't lighting, it could be because of a power issue or a damaged gauge. You should try replacing the fuse, ensuring the couplers are securely connected, replacing any damaged wires or hubs, or replacing the gauge.
What to do if Yamaha Outboard Motor trim gauge always shows fully tilted up position?
If the trim gauge always shows a fully tilted-up position, the trim sender signal is not being received. Connect the pink lead connectors to each other.
Why Yamaha Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Step-by-step instructions for safely removing the outboard motor from its shipping crate.
Details on how to correctly position and mount the outboard motor on the boat transom.
Lists specific propeller models and their applications for 2014 models.
Overview of throttle control systems and applicable models for remote controls.
Overview of the multi-function tiller handle and its electrical functions.
Procedures for mounting gauges, including angle and clearance requirements.
Functions and applications of the fuel management gauge.
Representative wiring diagram samples for remote controls and instruments.
Table of common troubles, causes, measures, and notes for digital network gauge systems.
Wiring diagrams for dual station applications with 6Y9 gauges for single, twin, and quad engines.
Details on recommended battery types, charging voltage, and capacity ratings for 4-stroke and 2-stroke engines.
Wiring examples for single and twin engine applications, including isolator-equipped models.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Step-by-step instructions for safely removing the outboard motor from its shipping crate.
Details on how to correctly position and mount the outboard motor on the boat transom.
Lists specific propeller models and their applications for 2014 models.
Overview of throttle control systems and applicable models for remote controls.
Overview of the multi-function tiller handle and its electrical functions.
Procedures for mounting gauges, including angle and clearance requirements.
Functions and applications of the fuel management gauge.
Representative wiring diagram samples for remote controls and instruments.
Table of common troubles, causes, measures, and notes for digital network gauge systems.
Wiring diagrams for dual station applications with 6Y9 gauges for single, twin, and quad engines.
Details on recommended battery types, charging voltage, and capacity ratings for 4-stroke and 2-stroke engines.
Wiring examples for single and twin engine applications, including isolator-equipped models.
General| Brand | Yamaha |
|---|---|
| Model | 85AET |
| Category | Outboard Motor |
| Language | English |
To Next Page
