What to do if my Yamaha Recording Equipment won't turn on and the display is dark?
If your Yamaha Recording Equipment won't power on and the display remains dark, there are a few things to check: * Ensure the power cable is properly connected. * Make sure the POWER switch is turned on. * If the backlight setting is on “Auto OFF”, and you prefer it to stay lit, change the “5. Utility” ? “LCD Backlight” setting to “ON.”
Why I cannot edit parameters on my Yamaha ACD1 Control Unit?
If you cannot edit parameters on your Yamaha Control Unit, it might be due to Panel Lock being enabled. To solve this, change the “5. Utility” ? “Panel Operation” setting to Normal, or use Amp Editor to disable Panel Operation. Another reason may be that you are attempting to edit a parameter of an amplifier that is not connected or powered on. Ensure the amplifier is connected and powered on.
What to do if all scene data saved in the ACD1 Yamaha Control Unit has disappeared?
If all scene data saved in your Yamaha ACD1 Control Unit has disappeared, it could be due to a few reasons. One possibility is that the power was turned off while the ACD1’s data was being saved. In this case, synchronize the unit with Amp Editor to transmit the settings from Amp Editor again. Another reason might be that the internal battery has run down. Check the battery status by going to “5. Utility” ? “Battery”. If the indication is “Low Battery” or “No Battery,” contact your Yamaha dealer to have the battery replaced.
How to fix Yamaha ACD1 when power will not turn on and display will not light?
If your Yamaha Control Unit's power will not turn on and the display does not light up, ensure the power cable is properly connected and the POWER switch is turned on. Also, check if the backlight setting is set to “Auto OFF”. If it is, and you want the LCD backlight to stay lit, turn the “5. Utility” ? “LCD Backlight” setting “ON.”
What to do if I can’t monitor or control an amplifier using my Yamaha ACD1 Control Unit?
If you can’t monitor or control an amplifier with your Yamaha Control Unit, check if any cables are disconnected or broken. Also, verify that no cable exceeds the allowable length: the cable connected to the [MONITOR/REMOTE] connector should be no longer than 50 meters, the cable connected to the [DATA PORT] connector should extend no longer than a total of 500 meters to its last point, and each individual cable between your computer and the ACD1 should be no longer than 100 meters. Ensure that in the middle of a daisy-chain there isn't an amplifier whose T-switch is ON; turn off the T-switch for all amplifiers other than the last amplifier.
Why can't I edit parameters on my Yamaha Recording Equipment?
If you're unable to edit parameters on your Yamaha Recording Equipment, consider these possibilities: 1. Panel Lock might be enabled. Change the “5. Utility” ? “Panel Operation” setting to Normal, or use Amp Editor to disable Panel Operation. 2. You might be trying to adjust settings for an amplifier that isn't connected. Ensure the amplifier you want to modify is properly connected. 3. The corresponding amplifier might not be powered on. Power on the amplifier you wish to adjust.
What to do if all scene data disappeared from my Yamaha ACD1 Recording Equipment?
If all scene data has disappeared from your Yamaha ACD1 Recording Equipment, here's what you should do: * If the power was turned off while the ACD1’s data was being saved, synchronize the unit with Amp Editor again to transmit the settings from Amp Editor. * If the internal battery has run down, go to “5. Utility” ? “Battery” to check the battery status. If the indication is “Low Battery” or “No Battery,” replace the battery.
General| Type | Control Unit |
|---|---|
| Manufacturer | Yamaha |
| Model | ACD1 |
| Sampling Frequency | 44.1kHz, 48kHz, 88.2kHz, 96kHz |
| Bit Depth | 24-bit |
| Input | Analog XLR, Digital AES/EBU |
| Output | Analog XLR, Digital AES/EBU |
| Control Interface | Ethernet |
To Next Page
