To Next PageTo Next Page
Need help?Do you have a question about the Yamaha DSP-AX640 and is the answer not in the manual?
General| Type | AV Receiver |
|---|---|
| Channels | 6.1 |
| Amplifier Type | Discrete |
| Input Sensitivity/Impedance | 200 mV/47 kΩ |
| Audio Decoders | Dolby Digital, DTS, Dolby Pro Logic II |
| Analog Inputs | 5 |
| HDMI | No |
| Digital audio input | Yes |
| Output Power per Channel | 100W |
| Frequency Response | 10 Hz - 100 kHz |
| Total Harmonic Distortion | 0.06% |
| Signal-to-Noise Ratio | 100 dB |
| Speaker Impedance | 6 ohms |
| Surround Sound Processing | Dolby Digital, DTS |
| Digital Inputs | 2 Optical, 2 Coaxial |
| Dimensions (W x H x D) | 435 x 171 x 413 mm |
Information for authorized service personnel regarding critical components and safety procedures.
Post-service test for insulation and leakage current limits to ensure safety.
Detailed specifications for the audio amplifier section, including output power and frequency response.
Step-by-step instructions for removing the top cover of the unit.
Step-by-step instructions for removing the DSP P.C.B. and its support.
Instructions for removing various FUNCTION P.C.B.s and the tuner.
Instructions for removing the MAIN and POWER P.C.B.s.
Instructions for removing the front panel unit.
Procedures for removing the sub chassis and side plates.
Lists the 15 diagnostic menu items and their sub-menu items for troubleshooting.
Continues the list of diagnostic menu items and their sub-menu items.
Instructions on how to initiate the DIAG mode by pressing specific keys on the main unit.
Explains the display output when DIAG is initiated, including version and menu list.
Explanation of protection triggered by abnormal DC output from the power amplifier.
Lists functions available while operating in DIAG mode, such as input selection and level adjustment.
Procedure to enter DIAG mode with protection functions disabled to aid diagnosis.
Describes the display when no protection function history is present.
Explanation of protection triggered by excessive heat sink temperature.
Steps to take before canceling DIAG, including setting PRESET and turning off the power.
Describes the display when protection function history exists.
Explanation of protection triggered by abnormal power supply voltage.
Explains how to navigate and select menu items and sub-menus within the DIAG function.
Explains DSP through modes like ANALOG BYPASS, YSS 0dB, YSS Front 0dB, including head margin characteristics.
Describes digital full-bit output without head margin and SWFR signal output.
Information about RAM throughput for YSS938, outputting CT signal through Sub DSP-DRAM.
Details Pro-Logic processing for L/C/R/RL/RR signals, outputting C/RL/RR via Sub DSP-DRAM.
Explains Neo:6 processing by CS49329 and output via Sub DSP-DRAM; fixed to Cinema 6ch mode.
Describes how input signals are identified and switched based on priority.
Explains signal output including head margin, with specific checks for MAIN 12dB and 18dB.
Describes signal input through 6CH INPUT terminals and outputting to EXTERNAL DECODER.
Noise generator outputs test signals through specified channels, with details on frequency and output.
Displays A/D conversion values for terminals detecting panel keys and protection functions.
Information on impedance switch and power limiter detection values.
Displays status data of the microprocessor in hexadecimal notation.
Details signal processing status, including mute request, DTS flashing, and analog mute.
Self-diagnosis of bus connection for YSS938 and external RAM.
Switches function settings on P.C.B. via software to activate the product.
Displays microprocessor version, checksum, and specified port status.
Program to check the FL display section, including various display states and signal processing.
Menu to reserve and inhibit initialization of backup RAM, with options for PRESET INHIBIT and PRESET RESERVED.
Checks the functionality of panel keys and how to verify their constants.
Displays channel status information of the input signal (IEC60958).
Displays data version of FLASH ROM, TOC information, and sum calculated value for the second decoder.
Displays information of the bit stream included in the DOLBY DIGITAL signal.
Displays information of the bit stream included in the dts signal.
