To Next PageTo Next PageWhat to do if the desired station cannot be tuned in with the automatic tuning method on my Yamaha Receiver?
If you cannot tune into the desired station with the automatic tuning method on your Yamaha Receiver, the signal may be weak or the antenna connections may be loose. Tighten the AM loop antenna connections and orient it for best reception.
Why does the sound suddenly go off on my Yamaha DSP-AX630SE Receiver?
The sound on your Yamaha Receiver might suddenly go off due to several reasons: * The protection circuit may have been activated due to a short circuit. Check that the IMPEDANCE SELECTOR switch is in the correct position and turn the unit back on. * Ensure that the speaker wires are not touching each other, then turn the unit back on. * The sleep timer may have activated. Turn the power back on and play the source again. * The sound may be muted. Press the MUTE button or any other operation button to cancel the mute function and adjust the volume.
How to fix a Yamaha DSP-AX630SE remote control that is not working?
If your Yamaha Receiver remote control is not working properly, try the following: * Ensure you are within a 6 m (20 feet) range and no more than 30 degrees off-axis from the front panel. * Replace all batteries with new ones. * Make sure the manufacture code is correctly set.
Why can I only hear sound from one speaker on my Yamaha DSP-AX630SE?
If you only hear sound from one speaker connected to your Yamaha Receiver: * Check the cable connections to ensure they are properly connected. If the problem persists, the cables may be defective. * Verify the “5 L/R BALANCE” setting in the SET MENU and adjust it to the appropriate position.
What to do if there is no sound from the subwoofer connected to my Yamaha Receiver?
If you are not getting any sound from the subwoofer connected to your Yamaha Receiver: * Check that “1E BASS” on the SET MENU is set to SWFR or BOTH when a Dolby Digital or DTS signal is being played. * If you are playing a 2-channel source, ensure “1E BASS” on the SET MENU is set to BOTH.
How to eliminate continuous crackling and hissing noises from my Yamaha Receiver?
If you are experiencing continuous crackling and hissing noises with your Yamaha Receiver, these noises may result from lightning, fluorescent lamps, motors, thermostats, and other electrical equipment. Try using an outdoor antenna and a ground wire. This may help somewhat, but it is difficult to eliminate all noise.
Why does my Yamaha DSP-AX630SE suddenly turn into standby mode?
If your Yamaha Receiver suddenly turns into standby mode, the internal temperature may have become too high, activating the overheat protection circuitry. Wait until the unit cools down and then turn it back on.
How to fix noisy FM stereo reception on my Yamaha Receiver?
If you are experiencing noisy FM stereo reception on your Yamaha Receiver, check the antenna connections. Try using a high-quality directional FM antenna, as the characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor.
What should I do if my Yamaha DSP-AX630SE Receiver does not operate properly?
If your Yamaha Receiver is not operating properly, the internal microcomputer may have been frozen. Disconnect the AC power cord from the outlet and then plug it in again after about 30 seconds.
Why is my Yamaha DSP-AX630SE making a humming sound?
A humming sound from your Yamaha Receiver could be due to incorrect cable connections. Ensure that the audio plugs are firmly connected. If the problem persists, the cables may be defective.
General| Type | AV Receiver |
|---|---|
| Audio Channels | 6.1 |
| Total Harmonic Distortion (THD) | 0.06% |
| Input Impedance | 47 kOhms |
| Input Sensitivity | 200 mV |
| Signal to Noise Ratio | 100 dB |
| Tuner Section | FM/AM |
| Surround Sound Formats | Dolby Digital, DTS |
| FM Sensitivity | 1.0 µV |
| Video Section | Composite Video, S-Video |
| Dimensions | 435 x 171 x 421 mm |
| Amplifier Section | Discrete |
Instructions on connecting and positioning speakers for optimal sound.
Overview of all connection types and ports available on the unit.
How to select sources, adjust volume, and play audio or video content.
Accessing and adjusting various settings via the SET MENU.
Fine-tuning output levels for center, rear, and subwoofer speakers.
Solutions for common operational problems and issues.
