General specifications
Maximum output power
STEREO: 300 W+300 W/4Ω @0.5% THD at 1 kHz
215 W+215 W/8Ω @0.5% THD at 1 kHz
BRIDGE: 600 W/8Ω @0.5% THD at 1 kHz
Frequency response
20 Hz~20 kHz +1 dB, –3 dB
@1 W output into 8Ω
(SPEAKER OUT)
Channel Gain control at minimum.
20 Hz~20 kHz +1 dB, –3 dB
@+4 dB output into 600Ω
(ST OUT, MONO OUT, EFFECT
SEND, MONITOR OUT)
Channel Gain control at minimum.
Total harmonic distortion
Less than 0.5% @20 Hz~20 kHz, 150 W output into 4Ω (SPEAKER OUT)
Less than 0.3% @20 Hz~20 kHz, +14 dB output into 600Ω
(ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT)
Hum & noise
(Average, Rs=150Ω )
(with 20 Hz~20 kHz BPF)
–128 dB equivalent input noise
–63 dB residual output noise (SPEAKER OUT)
–95 dB residual output noise (ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT)
–87 dB
(ST OUT, MONO OUT)
ST master/MONO master fader at maximum level and all
channel fader at minimum.
–64 dB (68 dB S/N)
(ST OUT, MONO OUT)
ST master/MONO master fader and 1 channel fader at maxi-
mum level. And 1 channel Gain control at maximum.
–80 dB
(EFFECT SEND, MONITOR OUT)
Master fader at maximum level and all channel level control
at minimum.
Maximum voltage gain
91 dB MIC IN to SPEAKER OUT (CH 1~8)
64 dB MIC IN to ST OUT (CH 1~8)
38 dB LINE IN to ST OUT (CH 1~8)
38 dB ST IN to ST OUT (CH 9/10, 11/12)
70 dB MIC IN to EFFECT SEND (CH 1~8)
64 dB MIC IN to MONITOR OUT (CH 1~8)
Crosstalk at 1 kHz
–70 dB adjacent input, –70 dB input to output
MIC IN gain control
44 dB variable
POWER AMP level control
14 dB variable
Input channel equalization
HIGH 10 kHz shelving*
MID 2.5 kHz peaking
LOW 100 Hz shelving*
* Turn over/roll off frequency of shelving: 3 dB below maximum variable level.
Meters
13 points LED meter
CH peak indicators
Red LED on each channel lits when POST EQ signal reaches the level –3 dB below clipping.
Limiter
Comp. : THD≥0.5%
LIMIT indicators
Turn on THD≥0.5%
Graphic equalizer
7 bands (125, 250, 500, 1k, 2k, 4k, 8k Hz), ±12 dB Maximum
Internal digital effect
16 programs, PARAMETER control
Foot switch
Digital effect mute: on/off
Protection circuit (Power amp)
POWER switch on/off mute, DC detection, TEMP (heatsink temp. ≥90°C)
Fan circuit
stop — low speed (50°C) — variable — high speed (70°C)
Phantom power
+48 V is supplied to electrically balanced inputs.
Option
FC5 (Foot switch)
Power requirement/
Power consumption
USA and Canada:120 V AC 60 Hz, 250 W
Europe: 230 V AC 50 Hz, 300 W
Other: 240 V AC 50 Hz, 300 W
Dimensions (WxHxD)
480
XX
125 454 mm
Weight
16 kg
Accessories
Power cord, Owner’s Manual
To Next Page
Loading...
Need help?
General
