What to do if Yamaha F200BET fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
Why Yamaha Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
How to fix Yamaha Outboard Motor trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha Outboard Motor Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
What to do if Yamaha Outboard Motor gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
What causes Yamaha F200BET Outboard Motor fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
How to fix Yamaha F200BET Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
Why Yamaha Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
What to do if the Yamaha Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
General| Brand | Yamaha |
|---|---|
| Model | F200BET |
| Category | Outboard Motor |
| Language | English |
Provides guidance on correctly mounting the outboard motor for optimal performance.
Guides on the correct installation of the remote oil tank, including notices for mounting.
Explains the two throttle control systems and compatibility of models.
Details the features and compatibility of the 703 side mount mechanical remote control.
Describes the 704 binnacle mount mechanical remote control for electric start models.
Details the 6X3 concealed mechanical remote control for runabout boats with emergency switch.
Describes the 6X5 binnacle mount mechanical remote control for triple engine applications.
Introduces the 6X6 binnacle mount DEC remote control, requiring no mechanical cables.
Details the 6X7 concealed DEC remote control, requiring no mechanical cables.
Details the combination switch panel with IG switch and emergency stop switch.
Details emergency stop switches with panels for various applications.
Provides information on selecting the correct remote control cable length.
Explains how to adjust the free play of the mechanical remote control throttle cable.
Details attachment kits for remote controls, including torque specifications.
Details the steering guide attachment kit and its components for various engine models.
Details main wire harnesses and dual station wire harnesses for DEC systems.
Introduces the multi-function tiller handle with electrical functions and kit preparation.
Provides a wiring diagram for the 6X4 multi-function tiller handle in US configurations.
Provides a wiring diagram for the 6X4 multi-function tiller handle in Japanese configurations.
Provides contents for the handle immobilizer kit for F30B to F115B models.
Shows the wiring diagram for the 6X4 multi-function tiller handle in EU and ANZ configurations.
Details procedures for mounting gauges, including angle requirements and stud tightening.
Provides information on analog tachometers, including applications and dimensions.
Covers digital tachometers, including applications, dimensions, and setup procedures.
Details speedometer types, applications, dimensions, and tube routing.
Explains the fuel management gauge functions, applications, and kit contents.
Provides information on analog trim meters, including applications and dimensions.
Details coolant pressure meters, including applications, dimensions, and installation.
Covers coolant temperature meters, including applications, dimensions, and installation.
Provides information on hour meters, including applications, dimensions, and wiring.
Details voltage meters, including types, dimensions, and wiring.
Covers fuel meters, including types, applications, dimensions, and wiring.
Explains the charge warning unit's types, applications, and wiring.
Provides representative wiring diagrams for Yamaha remote controls and instruments.
Shows the wiring diagram for a single engine application with 6Y5 digital meters.
Provides the wiring diagram for single engine applications with side-mount RC and specific engine models.
Shows the wiring diagram for single engine applications with binnacle RC.
Provides the wiring diagram for twin engine applications with 6Y5 gauges and binnacle RC.
Shows the wiring diagram for analog meters with 2-stroke engines and premixed applications.
Provides wiring diagrams for analog meters on 2- and 4-stroke engines with specific applications.
Shows wiring diagrams for digital tachometers on 4-stroke engines.
Provides wiring diagrams for digital tachometers on 2-stroke engines.
Provides information on digital network gauges, including compatible models and applications.
Details the speed sensor kit for pitot tube pressure measurement.
Guides on the installation of the coolant pressure sensor kit.
Describes the wire for powering the immobilizer unit.
Explains the function of the network hub for distributing signals and power to gauges.
Guides on connecting NMEA2000 compatible equipment to the network hub.
Details connecting analog gauges to the network hub.
Explains the immobilizer unit and its acceptable models.
Shows the wiring diagram for single engine applications with specific engine types.
Provides a simple wiring diagram for twin engine applications with specific engine types.
Details a deluxe wiring diagram for twin engine applications with specific engine types.
Shows the wiring diagram for triple engine applications with specific engine types.
Guides on the initial setup for digital network gauges when multiple engines are installed.
Explains how to set the gauge when a 6Y9 multi-sensor is connected for sensor enabling.
Provides a table of common system or gauge issues and their solutions.
Provides information on digital network premium gauges, compatible models, and applications.
Shows the wiring diagram for single station applications with 6Y9 gauges and 6X6 binnacle mount DEC.
Provides the wiring diagram for single station applications with 6Y8 gauges and 6X6 binnacle mount DEC.
Shows the wiring diagram for single station applications with 6Y9 gauges and 6X7 concealed DEC.
Provides the wiring diagram for single station applications with 6Y8 gauges and 6X7 concealed DEC.
Shows the wiring diagram for twin engine applications with 6Y9 gauges.
Provides the wiring diagram for twin engine applications with 6Y8 gauges.
Shows the wiring diagram for triple engine applications with 6Y9 gauges.
Provides the wiring diagram for triple engine applications with 6Y8 gauges.
Provides the wiring diagram for dual station single engine applications with 6Y9 gauges.
Shows the wiring diagram for dual station single engine applications with 6Y8 gauges.
Shows the wiring diagram for dual station quad engine applications with 6Y9 gauges.
To Next Page
