EasyManua.ls Logo

Yamaha F200B - Service Manual

Yamaha F200B
579 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
F200B
FL200B
F250G
FL250G
SERVICE MANUAL
6DX-28197-5P-11

Table of Contents

Other manuals for Yamaha F200B

Preview: Rigging Guide
Rigging Guide329 pages
Preview: Owner's Manual
Owner's Manual122 pages

Questions and Answers

  • E
    Elizabeth MaysAug 19, 2025
    Why does my Yamaha F200B warning buzzer sound?
    • E
      Emily BarrAug 20, 2025
      The warning buzzer or indicator lamp might activate due to several reasons: * The cooling system could be clogged, so check the water intake for any restrictions. * The engine oil level might be low; if so, fill the oil tank with the specified engine oil. * The specified engine oil might not be used; in this case, replace the oil with the specified type. * The engine oil might be contaminated or deteriorated; if so, replace it with fresh, specified type. * The load on the boat may be improperly distributed; distribute the load to place the boat on an even plane.
  • T
    Travis MaxwellAug 23, 2025
    How to troubleshoot a Yamaha F200B Outboard Motor when the starter won't operate?
    • J
      Jenna RiceAug 23, 2025
      If the starter on your Yamaha Outboard Motor won't operate, try these steps: 1. Check the battery condition and use a battery of the recommended capacity if it's weak or low. 2. Tighten battery cables and clean battery terminals if the connections are loose or corroded. 3. Check for a blown fuse in the electric start circuit; find the cause of the overload and repair it, then replace the fuse with one of the correct amperage. 4. Shift to neutral, if the shift lever is in gear.
  • J
    James HarmonAug 26, 2025
    What to do if my Yamaha F200B Outboard Motor gauge display does not wake up?
    • M
      Michael VasquezAug 26, 2025
      If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or replace the gauge itself.
  • M
    Matthew PerezAug 27, 2025
    Why is the illumination not lighting on my Yamaha F200B Outboard Motor gauge?
    • M
      Madison HenryAug 27, 2025
      If the illumination isn't lighting, it could be because of a power issue or a damaged gauge. You should try replacing the fuse, ensuring the couplers are securely connected, replacing any damaged wires or hubs, or replacing the gauge.
  • L
    Leonard PhamAug 29, 2025
    Why does my Yamaha F200B Outboard Motor fuel management gauge show incorrect fuel consumption?
    • P
      pricemiguelAug 30, 2025
      If the fuel management gauge shows incorrect fuel consumption, the engine recognition may be wrong. To resolve this, default the engine number. Then, turn the key switch on in order from the portside engine to re-memorize each engine number.
  • B
    Blake WhiteAug 31, 2025
    How to fix a Yamaha Outboard Motor tachometer that shows incorrect engine RPM?
    • M
      Melissa LewisAug 31, 2025
      If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong. Push the SET button for 10 seconds to default the engine number, and then memorize each engine number again.
  • J
    Jeremy BlackSep 2, 2025
    What to do if my Yamaha Outboard Motor speedometer shows the incorrect fuel level?
    • J
      Jennifer ClarkSep 3, 2025
      If the speedometer shows an incorrect fuel level, the fuel sensor selection is likely wrong. You should set up the fuel sensor to the correct resistance.
  • B
    Brooke LawrenceSep 4, 2025
    What does it mean when my Yamaha Outboard Motor gauge shows “----”?
    • M
      Michael ReyesSep 5, 2025
      If the gauge shows “----”, it indicates that the digital signal is not being received. Make sure the couplers are securely connected and replace any damaged bus wires or hubs.
  • D
    David MunozSep 6, 2025
    Why does my Yamaha F200B fuel management gauge show incorrect remaining fuel?
    • K
      karinaalexanderSep 6, 2025
      If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting is probably wrong. Fill the tank with fuel, and then set the correct fuel tank capacity.
  • D
    Daniel StephensonSep 8, 2025
    Why does my Yamaha Outboard Motor trim gauge show the incorrect position?
    • D
      Debbie YoungSep 9, 2025
      If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sensor could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sensor.

Yamaha F200B Specifications

General IconGeneral
Full Throttle RPM Range5000 - 6000 RPM
Starting SystemElectric
Recommended FuelRegular Unleaded
Recommended OilYamalube 4M
SteeringRemote
Engine Type4-Stroke
Displacement2785 cc
Max Output200 hp @ 5500 rpm
Bore x Stroke96 mm x 96.2 mm
Fuel Induction SystemElectronic Fuel Injection
IgnitionTCI
Prop Shaft Length20" / 25"
Alternator Output50 amps

Related product manuals