What to do if Yamaha Outboard Motor fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
What to do if the Yamaha F20AET Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha F20AET Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha F20AET Outboard Motor fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
What to do if Yamaha F20AET gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha F20AET Outboard Motor Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
How to fix Yamaha Outboard Motor trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha F20AET gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
What causes Yamaha Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
General| Brand | Yamaha |
|---|---|
| Model | F20AET |
| Category | Outboard Motor |
| Language | English |
Important safety instructions regarding potential severe injury or death.
Explains pictographs for crate handling and product protection.
Step-by-step guide for safely removing the outboard motor from its shipping crate.
Provides guidance on correctly mounting the outboard motor onto the boat's transom.
Guidance on installing the remote oil tank for specific engine types.
Guidance on selecting the appropriate propeller for optimal engine speed and load.
Table showing recommended engine RPM ranges for various models at Wide-Open-Throttle.
Explains throttle control systems and models using specific connectors.
Introduces multi-function tiller handle kits for various Yamaha engines.
Lists contents for tiller handle kits for US market engines.
Details the multi-function tiller handle kit for Japanese market engines.
Step-by-step procedure for mounting gauges to the instrument panel.
Details the fuel management gauge, its functions, and applications.
Instructions for initial setup of digital network gauges, especially for multi-engine setups.
Table of common troubleshooting issues and their solutions for the gauge system.
Details recommended battery specifications for various Yamaha outboard engines.
Wiring instructions for battery systems, including isolator equipped models.
Standard vacuum pressure requirements for the fuel system.
Checklist for pre-delivery inspection of outboard motors.
To Next Page
