To Next Page
C
clarenceandersonSep 6, 2025
How to setup Yamaha Outboard Motor tachometer to show the oil pressure?
- EelizabethpalmerSep 6, 2025
Select the oil press. display.
How to setup Yamaha Outboard Motor tachometer to show the oil pressure?
Select the oil press. display.
What to do if the Yamaha Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha FL115AET Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha FL115AET tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha Outboard Motor fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
What to do if Yamaha FL115AET gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
What to do if my Yamaha FL115AET Outboard Motor speedometer shows the incorrect fuel level?
If the speedometer shows an incorrect fuel level, the fuel sensor selection is likely wrong. You should set up the fuel sensor to the correct resistance.
Why Yamaha Outboard Motor boat speed and/or coolant pressure gauge does not show?
If the boat speed and/or coolant pressure gauge does not show, it is likely that the optional sensor has not been installed. Install the optional sensor.
What causes Yamaha FL115AET Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
What to do if Yamaha FL115AET trim gauge always shows fully tilted up position?
If the trim gauge always shows a fully tilted-up position, the trim sender signal is not being received. Connect the pink lead connectors to each other.
General| Horsepower | 115 hp |
|---|---|
| Cylinders | 4 |
| Starting System | Electric |
| Steering | Remote |
| Trim System | Power Trim and Tilt |
| Fuel System | Electronic Fuel Injection |
| Fuel Induction System | EFI |
| Shaft Length | 20 in |
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates special precautions that must be taken to avoid damage to the products or other property.
Details the steps to uncrate the outboard motor.
Describes proper motor mounting for performance and reliability.
Guidance on choosing the right propeller based on applications.
Table showing RPM ranges for different engines.
WOT RPM ranges for 2-stroke engines.
WOT RPM ranges for 4-stroke engines.
Describes different types of remote controls.
Description of the multi-function tiller handle.
Procedures for mounting instrument gauges.
Applications and descriptions of analog tachometers.
Applications and descriptions of digital tachometers.
Types and applications of speedometers.
Functions and applications of fuel management gauges.
Provides wiring diagrams and color codes.
Procedure for setting up digital network gauges.
Common problems and solutions for the system.
Wiring diagrams for various dual station setups.
Lists battery specifications by model.
Explains wiring for isolator-equipped and twin-engine setups.
Checklist for pre-delivery inspection.
