What to do if my Yamaha Minidisc Recorder won't record?
If your Yamaha Minidisc Recorder isn't recording, ensure the disc's write protect tab is set to unprotect. Also, be sure to press a [REC SELECT] button to select a track for recording and verify that you have assigned the signal you want to record to the track. Finally, use the CUE monitor controls to check if the signal is actually being sent to the track.
How to turn on a Yamaha Minidisc Recorder MD4?
To turn on your Yamaha Minidisc Recorder MD4, ensure the power cord is connected to a suitable AC wall outlet and plugged into the AC IN connector at the rear of the MD4. Also, make sure that the MD4 POWER switch is set to the ON position. If it still does not turn on, contact your Yamaha dealer.
Why can't I hear music from a connected source on my Yamaha MD4 Minidisc Recorder?
If you cannot hear a connected music source on your Yamaha Minidisc Recorder, ensure the input selector switch is set to MIC/LINE. Raise the input channel fader, assign the input channel to a track using the GROUP ASSIGN switches, and press the corresponding MONITOR SELECT GROUP switch. Finally, turn up the MONITOR LEVEL control.
How to synchronize a MIDI sequencer to my Yamaha Minidisc Recorder MD4?
To synchronize a MIDI sequencer to your Yamaha Minidisc Recorder MD4, make sure that your MIDI sequencer supports MTC or MIDI Clock. Ensure that the MD4’s MTC or CLK function is turned on. MTC appears on the display when MTC is used and MASTER appears when MIDI Clock is used. Also, make sure your MIDI sequencer is set to synchronize to an external MTC or MIDI Clock source. MD4 can locate quickly, so some MIDI sequencers may not be able to synchronize immediately, especially when MD4 is in A–B Repeat mode.
What to do if my Yamaha MD4 cannot record four tracks?
If your Yamaha Minidisc Recorder cannot record four tracks, make sure that you are using an MD DATA disc, not a MiniDisc.
Why don't the level meters show signal on my Yamaha MD4 Minidisc Recorder?
Normally, the level meters indicate disc signal levels. To see the level of a group signal you must press the [REC] button to engage Record Pause mode and press the corresponding [REC SELECT] button. With no disc loaded the meters indicate group signal levels.
Why can't I use Punch In/Out or Ping-Pong on my Yamaha Minidisc Recorder?
If a song was edited on another MD device, your Yamaha Minidisc Recorder MD4 may not be able to use these functions. In this case, try copying the song with the Song Copy function and then try and edit the copy. Songs recorded on other MD equipment may be protected by the SCMS protection system, and in this case, editing is not allowed.
How do I send a channel signal to the AUX SEND on my Yamaha Minidisc Recorder?
To send a channel signal to the AUX SEND on your Yamaha Minidisc Recorder, turn up the AUX control and raise the channel fader. This is because the AUX SEND signal is sourced post-fader (i.e., after the fader).
Why do recordings play back at the wrong pitch on my Yamaha Minidisc Recorder?
Recordings may play back at the wrong pitch on your Yamaha Minidisc Recorder if you adjusted the pitch prior to recording a track. Reset the pitch as required.
Why can't I rehearse on my Yamaha Minidisc Recorder?
You cannot rehearse the first recording on a blank disc with your Yamaha Minidisc Recorder. Record something first, then use the Rehearse function.
General| Type | 4-track MiniDisc recorder |
|---|---|
| Number of Tracks | 4 |
| Sampling Rate | 44.1 kHz |
| Bit Depth | 16-bit |
| Recording Format | Minidisc (MD) |
| Frequency Response | 20 Hz to 20 kHz |
| S/N Ratio | 90dB |
| Inputs | 4 x XLR/TRS combo |
| Outputs | 2 x RCA |
| EQ | 2-band EQ per channel |
| Effects | Reverb, Chorus, Delay |
| Recording Time | Up to 74 minutes (using 74-minute MiniDisc) |
| Signal-to-Noise Ratio | 90dB |
| Power Supply | AC 120V, 60 Hz |
| THD | Less than 0.05% |
To Next Page
