To Next PageTo Next PageWhat to do if my Yamaha Minidisc Recorder won't record?
If your Yamaha Minidisc Recorder isn't recording, ensure the disc's write protect tab is set to unprotect. Also, be sure to press a [REC SELECT] button to select a track for recording and verify that you have assigned the signal you want to record to the track. Finally, use the CUE monitor controls to check if the signal is actually being sent to the track.
How to turn on a Yamaha Minidisc Recorder MD4?
To turn on your Yamaha Minidisc Recorder MD4, ensure the power cord is connected to a suitable AC wall outlet and plugged into the AC IN connector at the rear of the MD4. Also, make sure that the MD4 POWER switch is set to the ON position. If it still does not turn on, contact your Yamaha dealer.
Why can't I hear music from a connected source on my Yamaha MD4 Minidisc Recorder?
If you cannot hear a connected music source on your Yamaha Minidisc Recorder, ensure the input selector switch is set to MIC/LINE. Raise the input channel fader, assign the input channel to a track using the GROUP ASSIGN switches, and press the corresponding MONITOR SELECT GROUP switch. Finally, turn up the MONITOR LEVEL control.
How to synchronize a MIDI sequencer to my Yamaha Minidisc Recorder MD4?
To synchronize a MIDI sequencer to your Yamaha Minidisc Recorder MD4, make sure that your MIDI sequencer supports MTC or MIDI Clock. Ensure that the MD4’s MTC or CLK function is turned on. MTC appears on the display when MTC is used and MASTER appears when MIDI Clock is used. Also, make sure your MIDI sequencer is set to synchronize to an external MTC or MIDI Clock source. MD4 can locate quickly, so some MIDI sequencers may not be able to synchronize immediately, especially when MD4 is in A–B Repeat mode.
What to do if my Yamaha MD4 cannot record four tracks?
If your Yamaha Minidisc Recorder cannot record four tracks, make sure that you are using an MD DATA disc, not a MiniDisc.
Why don't the level meters show signal on my Yamaha MD4 Minidisc Recorder?
Normally, the level meters indicate disc signal levels. To see the level of a group signal you must press the [REC] button to engage Record Pause mode and press the corresponding [REC SELECT] button. With no disc loaded the meters indicate group signal levels.
Why can't I use Punch In/Out or Ping-Pong on my Yamaha Minidisc Recorder?
If a song was edited on another MD device, your Yamaha Minidisc Recorder MD4 may not be able to use these functions. In this case, try copying the song with the Song Copy function and then try and edit the copy. Songs recorded on other MD equipment may be protected by the SCMS protection system, and in this case, editing is not allowed.
How do I send a channel signal to the AUX SEND on my Yamaha Minidisc Recorder?
To send a channel signal to the AUX SEND on your Yamaha Minidisc Recorder, turn up the AUX control and raise the channel fader. This is because the AUX SEND signal is sourced post-fader (i.e., after the fader).
Why do recordings play back at the wrong pitch on my Yamaha Minidisc Recorder?
Recordings may play back at the wrong pitch on your Yamaha Minidisc Recorder if you adjusted the pitch prior to recording a track. Reset the pitch as required.
Why can't I rehearse on my Yamaha Minidisc Recorder?
You cannot rehearse the first recording on a blank disc with your Yamaha Minidisc Recorder. Record something first, then use the Rehearse function.
General| Type | 4-track MiniDisc recorder |
|---|---|
| Number of Tracks | 4 |
| Sampling Rate | 44.1 kHz |
| Bit Depth | 16-bit |
| Recording Format | Minidisc (MD) |
| Frequency Response | 20 Hz to 20 kHz |
| S/N Ratio | 90dB |
| Inputs | 4 x XLR/TRS combo |
| Outputs | 2 x RCA |
| EQ | 2-band EQ per channel |
| Effects | Reverb, Chorus, Delay |
| Recording Time | Up to 74 minutes (using 74-minute MiniDisc) |
| Signal-to-Noise Ratio | 90dB |
| Power Supply | AC 120V, 60 Hz |
| THD | Less than 0.05% |
Highlights the key features of the MD4's mixer and recorder sections.
Turns on the Auto Punch In/Out function.
Accesses various functions like Rec Mode, Text, MIDI Sync.
Adjusts position of markers and LAST REC IN/OUT points.
Sets the Pitch mode (FIX or VARI).
Selects Time Counter mode (ELAPSE, REMAIN, TOTAL).
Controls playback, record, rehearse, pause, review, FF CUE, STOP.
Illustrates the basic equipment needed to start recording.
Step-by-step guide to record the initial track.
How to playback the first recorded track.
Recording new sounds over existing tracks while listening.
Mixing track signals into a stereo mix for final recording.
Explains how to monitor signals via headphones or speakers.
Guide to recording new songs sequentially on a disc.
Choosing between 4TR, 2TR, and MONO recording modes.
Performing manual punch in/out using the REC button.
Performing manual punch in/out using REC SELECT buttons.
Controlling manual punch in/out with an optional footswitch.
Setting punch points automatically during playback.
Practicing the Auto Punch In/Out sequence before actual recording.
Executing the Auto Punch In/Out sequence for recording.
Using a footswitch to control the Auto Punch sequence.
Adjusting time before IN and after OUT points for Auto Punch.
Bouncing tracks to free up space for further recording.
Steps to prepare for ping-pong recording.
Practicing the ping-pong operation.
Executing the ping-pong recording.
Combining ping-pong with overdub recording for simultaneous recording.
Changing pitch for playback and recording.
Returning the pitch setting to normal.
Overview of footswitch control for various MD4 modes.
Connecting and using effects processors during mixdown.
Using effects processors while recording tracks.
Using effects processors during ping-pong operations.
Duplicating a song, including its title, markers, and Tempo Map.
Splitting a song into multiple independent songs.
Merging adjacent songs that were previously divided.
Copying sections of a track using the Off Line Punch function.
Removing individual tracks from a song.
Integrating MD4 into a MIDI system for synchronization.
Diagram showing MD4 integration with MIDI devices and sequencers.
Configuring MD4 to output MIDI Timecode for synchronization.
Configuring the MIDI sequencer to receive MTC.
Configuring the MIDI sequencer to synchronize with MIDI Clock.
Recording all sounds simultaneously in a single take.
Advice for achieving a balanced stereo mix.
Provides advice for common symptoms and problems.
