MOX6/MOX8 Data List
86
Effect Parameter List
[7] NOISE GATE + COMP + EQ
Insertion L Block
[0] THRU
When this type is selected, no parameters are available.
[1] VOCODER
Master Effect Block
THRU type is not included in the Master Effect Block. If you wish to bypass this block, turn
the EFFECT [MASTER] button off.
DELAY L, R (Stereo)
LO-FI
COMP DISTORTION
ISOLATOR
DYNAMIC FILTER
SLICE
RING MODULATOR
MULTI BAND COMP
VCM COMPRESSOR 376
Master EQ Block
[0] MEQ
When the EQ Shape1 is set to Peaking, the range of EQ Frequency 1 is 63Hz – 2.0kHz (10 – 40).
No. Parameter Range Value
Table No.
1 Comp Attack 1ms – 40ms (0 – 19) 8
2 Comp Release 10ms – 680ms (0 – 15) 9
3 Comp Threshold -48dB – -6dB (79 – 121)
4 Comp Ratio 1.0 – 20.0 (0 – 7) 10
5 Comp Output Level 0 – 127 (0 – 127)
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 79.
10 —
11 Noise Gate Attack 1ms – 40ms (0 – 19)
12 Noise Gate Release 10ms – 680ms (0 – 15)
13 Noise Gate Threshold -73dB – -30dB (54 – 97)
14 EQ Mid Frequency 100Hz – 10.0kHz (14 – 54) 3
15 EQ Mid Gain -12dB – +12dB (52 – 76)
16 EQ Mid Width 0.1 – 12.0 (1 – 120)
No. Parameter Range Value
Table No.
1 Formant Shift -2, -1, 0, +1, +2 (62 – 66)
2 Formant Offset -63 – +63 (1 – 127)
3 Vocoder Attack 1ms – 200ms (0 – 29) 8
4 Vocoder Release 10ms – 3000ms (0 – 23) 9
5 Gate Switch Off/On (0 – 1)
6 Mic Gate Threshold -72dB – -30dB (55 – 97)
7 HPF Cutoff Frequency Thru, 500Hz – 16.0kHz (27 – 58) 3
8 HPF Output Level 0 – 127 (0 – 127)
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Mic Level 0 – 127 (0 – 127)
12 Inst Input Level 0 – 127 (0 – 127)
13 Noise Input Level 0 – 127 (0 – 127)
14 Output Level 0 – 127 (0 – 127)
15 BPF1 Gain -18dB – +18dB (46 – 82)
16 BPF2 Gain -18dB – +18dB (46 – 82)
17 BPF3 Gain -18dB – +18dB (46 – 82)
18 BPF4 Gain -18dB – +18dB (46 – 82)
19 BPF5 Gain -18dB – +18dB (46 – 82)
20 BPF6 Gain -18dB – +18dB (46 – 82)
21 BPF7 Gain -18dB – +18dB (46 – 82)
22 BPF8 Gain -18dB – +18dB (46 – 82)
23 BPF9 Gain -18dB – +18dB (46 – 82)
24 BPF10 Gain -18dB – +18dB (46 – 82)
No. Parameter Range Value
Table No.
1 EQ1 Gain -12dB – +12dB (52 – 76)
2 EQ1 Frequency 32Hz – 2.0kHz (4 – 40) 3
3 EQ1 Q 0.1 – 12.0 (1 – 120)
4 EQ1 Shape Shelving, Peaking (0 – 1)
5 EQ2 Gain -12dB – +12dB (52 – 76)
6 EQ2 Frequency 100Hz – 10kHz (14 – 54) 3
7 EQ2 Q 0.1 – 12.0 (1 – 120)
8—
9 EQ3 Gain -12dB – +12dB (52 – 76)
10 EQ3 Frequency 100Hz – 10kHz (14 – 54) 3
11 EQ3 Q 0.1 – 12.0 (1 – 120)
12 —
13 EQ4 Gain -12dB – +12dB (52 – 76)
14 EQ4 Frequency 100Hz – 10kHz (14 – 54) 3
15 EQ4 Q 0.1 – 12.0 (1 – 120)
16 —
17 EQ5 Gain -12dB – +12dB (52 – 76)
18 EQ5 Frequency 500Hz – 16kHz (28 – 58) 3
19 EQ5 Q 0.1 – 12.0 (1 – 120)
20 EQ5 Shape Shelving, Peaking (0 – 1)
To Next Page
Loading...
Need help?
General
