What to do if a Yamaha MTX3 Computer Hardware device is not found on the network?
If a device within the MTX system isn't found on the network, power on all devices and ensure they are correctly connected to the network.
What to do if the IP address was not set within 60 seconds of startup on Yamaha MTX3 Computer Hardware?
Check rear panel DIP switch 6 (IP Setting). If DIP switch 6 is set to “PC,” use MTX Editor or DHCP server to specify the device IP address.
Why have the settings saved in internal memory been lost on my Yamaha MTX3?
The settings saved in internal memory have been lost, because either the internal backup battery has run low, or the device has malfunctioned. In this case, contact your Yamaha dealer.
What happens if the internal backup battery is exhausted on Yamaha Computer Hardware?
If the internal backup battery of your Yamaha Computer Hardware has been completely exhausted or is not installed, the current settings will be lost when you turn off the power, and the device will revert to default values. Stop use immediately and contact your Yamaha dealer.
Why is the YDIF IN connector on my Yamaha MTX3 Computer Hardware not synchronized?
If the digital signal being input to the [YDIF IN] connector is not synchronized to the word clock of your Yamaha device, ensure that YDIF cables are properly connected and meet the required specifications.
How to change UNIT ID that is set to '00' on Yamaha MTX3?
If the UNIT ID is set to “00” on your Yamaha Computer Hardware, change it to a different value.
What to do if the SD memory card was not recognized on Yamaha Computer Hardware?
Use an SD memory card that complies with the specifications.
What to do if a preset recall attempt has failed on Yamaha MTX3 Computer Hardware?
Initialize the memory of the device (use rear panel DIP switches 7 and 8). If this does not solve the problem, contact your Yamaha dealer.
Why does my Yamaha Computer Hardware internal clock keep resetting?
If a problem has occurred with the internal clock of your Yamaha Computer Hardware and it has been initialized (January 1, 2000, 0:00), contact your Yamaha dealer. If this occurs only once, an abnormality was detected with the clock setting and it was initialized; use MTX Editor to set the time.
What to do if the UNIT ID is set to “00” on Yamaha MTX3?
Set the UNIT ID to something other than “00.”
Important information regarding battery usage, replacement, and safe disposal practices.
Essential safety guidelines covering electrical hazards, location, handling, and maintenance.
Overview of the MTX3's capabilities, including its processor, YDIF format, and control options.
Detailed explanation of the MTX3's front panel controls, displays, and indicators.
Description of all connectors and switches located on the rear panel of the MTX3.
Procedures for physically installing the MTX3 and connecting analog and digital audio sources.
A guide to diagnosing and resolving common operational problems with the MTX3.
A list of alert codes displayed on the MTX3 and corresponding actions to take.
Explains warning symbols and provides comprehensive safety instructions for using the apparatus.
General| Sample rate | 48 kHz |
|---|---|
| Frequency range | 20 - 20000 Hz |
| Channels quantity | 21 channels |
| Signal delay (@48kHz) | 2.5 ms |
| Supported sample rates | 44.1, 48 kHz |
| Output impedance | 75 Ω |
| Total Harmonic Distortion (THD) | 0.05 % |
| Phantom power | 48 V |
| AC input voltage | 100-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 50 W |
| Product color | Gray |
| Rack capacity | 1U |
| Rack mounting | Yes |
| Video capability | No |
| Nominal input level | -62 dBu |
| Cables included | AC |
| Number of Euroblock input connectors | 4 |
Weight and Dimensions| Depth | 362 mm |
|---|---|
| Width | 480 mm |
| Height | 44 mm |
| Weight | 4800 g |
To Next Page
