What happens when the internal backup battery runs extremely low on Yamaha MTX3 Computer Hardware?
If the internal backup battery has run extremely low on your Yamaha Computer Hardware, the current settings will be lost when you turn off the power, and the device will revert to default values. Please stop use immediately, and contact your Yamaha dealer.
Why can't the preset be recalled on Yamaha Computer Hardware?
If the preset could not be recalled on your Yamaha Computer Hardware: * The Preset selected for recall cannot be recalled as no data has been stored to it. * Another device may have been added after presets were stored. Please synchronize and check all Presets using MTX Editor, edit as necessary and store again.
What to do if SD memory card was not recognized on Yamaha Computer Hardware?
If the SD memory card is not recognized by your Yamaha Computer Hardware, use an SD memory card that complies with the specifications.
Why does my Yamaha Computer Hardware internal clock keep resetting?
If a problem has occurred with the internal clock of your Yamaha Computer Hardware and it has been initialized (January 1, 2000, 0:00), contact your Yamaha dealer. If this occurs only once, an abnormality was detected with the clock setting and it was initialized; use MTX Editor to set the time.
What to do if the digital signal being input to the [YDIF IN] connector is not synchronized to the word clock of Yamaha Computer Hardware?
Make sure that YDIF cables are properly connected. Use cables that meet the required specifications.
What to do if the IP address was not set within 60 seconds of startup on Yamaha MTX3 Computer Hardware?
Check rear panel DIP switch 6 (IP Setting). If DIP switch 6 is set to “PC,” use MTX Editor or DHCP server to specify the device IP address.
Why have the settings saved in internal memory been lost on my Yamaha MTX3?
The settings saved in internal memory have been lost, because either the internal backup battery has run low, or the device has malfunctioned. In this case, contact your Yamaha dealer.
How to fix a Yamaha MTX3 Computer Hardware device not found on the network?
Power on all devices in the system, and make sure that they are correctly connected to the network.
How to troubleshoot a Yamaha MTX3 Computer Hardware device that has not started up correctly?
Turn the power off, then turn on after waiting at least 6 seconds. If this does not solve the problem, initialize the memory (use rear panel DIP switches 7 and 8). Should this also fail, contact your Yamaha dealer.
What to do if a communication error occurred with the [DCP] connection on Yamaha Computer Hardware?
• If an error was shown in the DCP panel, refer to the DCP owner’s manual and take the appropriate action. • Ensure that the panel ID of the DCP units do not conflict. • Verify that the cables are correctly connected and are within the specified length.
Important information regarding battery usage, replacement, and safe disposal practices.
Essential safety guidelines covering electrical hazards, location, handling, and maintenance.
Overview of the MTX3's capabilities, including its processor, YDIF format, and control options.
Detailed explanation of the MTX3's front panel controls, displays, and indicators.
Description of all connectors and switches located on the rear panel of the MTX3.
Procedures for physically installing the MTX3 and connecting analog and digital audio sources.
A guide to diagnosing and resolving common operational problems with the MTX3.
A list of alert codes displayed on the MTX3 and corresponding actions to take.
Explains warning symbols and provides comprehensive safety instructions for using the apparatus.
General| Sample rate | 48 kHz |
|---|---|
| Frequency range | 20 - 20000 Hz |
| Channels quantity | 21 channels |
| Signal delay (@48kHz) | 2.5 ms |
| Supported sample rates | 44.1, 48 kHz |
| Output impedance | 75 Ω |
| Total Harmonic Distortion (THD) | 0.05 % |
| Phantom power | 48 V |
| AC input voltage | 100-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 50 W |
| Product color | Gray |
| Rack capacity | 1U |
| Rack mounting | Yes |
| Video capability | No |
| Nominal input level | -62 dBu |
| Cables included | AC |
| Number of Euroblock input connectors | 4 |
Weight and Dimensions| Depth | 362 mm |
|---|---|
| Width | 480 mm |
| Height | 44 mm |
| Weight | 4800 g |
To Next Page
