To Next Page
E
Eric StephensAug 30, 2025
What to do if devices with identical UNIT IDs were found connected within the same network on Yamaha MTX3 Computer Hardware?
- TTyler KimAug 31, 2025
Change the UNIT ID so that there are no duplicates.
What to do if devices with identical UNIT IDs were found connected within the same network on Yamaha MTX3 Computer Hardware?
Change the UNIT ID so that there are no duplicates.
What to do if a Yamaha MTX3 Computer Hardware device is not found on the network?
If a device within the MTX system isn't found on the network, power on all devices and ensure they are correctly connected to the network.
What to do if the UNIT ID is set to “00” on Yamaha MTX3?
Set the UNIT ID to something other than “00.”
What happens when the internal backup battery runs extremely low on Yamaha MTX3 Computer Hardware?
If the internal backup battery has run extremely low on your Yamaha Computer Hardware, the current settings will be lost when you turn off the power, and the device will revert to default values. Please stop use immediately, and contact your Yamaha dealer.
How to troubleshoot Yamaha MTX3 Computer Hardware that won't start correctly?
If your Yamaha Computer Hardware device fails to start correctly, turn the power off, wait at least 6 seconds, and then turn it back on. If the issue persists, initialize the memory using the rear panel DIP switches 7 and 8. If the problem continues, contact your Yamaha dealer.
How to change UNIT ID that is set to '00' on Yamaha MTX3?
If the UNIT ID is set to “00” on your Yamaha Computer Hardware, change it to a different value.
What happens if the internal backup battery is exhausted on Yamaha Computer Hardware?
If the internal backup battery of your Yamaha Computer Hardware has been completely exhausted or is not installed, the current settings will be lost when you turn off the power, and the device will revert to default values. Stop use immediately and contact your Yamaha dealer.
How to troubleshoot a Yamaha MTX3 Computer Hardware device that has not started up correctly?
Turn the power off, then turn on after waiting at least 6 seconds. If this does not solve the problem, initialize the memory (use rear panel DIP switches 7 and 8). Should this also fail, contact your Yamaha dealer.
How to fix a Yamaha MTX3 Computer Hardware device not found on the network?
Power on all devices in the system, and make sure that they are correctly connected to the network.
Why have the settings saved in internal memory been lost on my Yamaha MTX3?
The settings saved in internal memory have been lost, because either the internal backup battery has run low, or the device has malfunctioned. In this case, contact your Yamaha dealer.
Important information regarding battery usage, replacement, and safe disposal practices.
Essential safety guidelines covering electrical hazards, location, handling, and maintenance.
Overview of the MTX3's capabilities, including its processor, YDIF format, and control options.
Detailed explanation of the MTX3's front panel controls, displays, and indicators.
Description of all connectors and switches located on the rear panel of the MTX3.
Procedures for physically installing the MTX3 and connecting analog and digital audio sources.
A guide to diagnosing and resolving common operational problems with the MTX3.
A list of alert codes displayed on the MTX3 and corresponding actions to take.
Explains warning symbols and provides comprehensive safety instructions for using the apparatus.
General| Sample rate | 48 kHz |
|---|---|
| Frequency range | 20 - 20000 Hz |
| Channels quantity | 21 channels |
| Signal delay (@48kHz) | 2.5 ms |
| Supported sample rates | 44.1, 48 kHz |
| Output impedance | 75 Ω |
| Total Harmonic Distortion (THD) | 0.05 % |
| Phantom power | 48 V |
| AC input voltage | 100-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 50 W |
| Product color | Gray |
| Rack capacity | 1U |
| Rack mounting | Yes |
| Video capability | No |
| Nominal input level | -62 dBu |
| Cables included | AC |
| Number of Euroblock input connectors | 4 |
Weight and Dimensions| Depth | 362 mm |
|---|---|
| Width | 480 mm |
| Height | 44 mm |
| Weight | 4800 g |
