Yamaha MX49 - Appendix: Functions and Messages; Shift Function List; Display Messages Overview

MX49/MX61 Data List
35
Effect Parameter List
[3] SPX CHORUS
*2: Insertion Block only.
[4] SYMPHONIC
*2: Insertion Block only.
[5] ENSEMBLE DETUNE
Category — FLANGER
[1] VCM FLANGER
[2] CLASSIC FLANGER
[3] TEMPO FLANGER
*2: Insertion Block only.
Category — PHASER
[1] VCM PHASER MONO
The Color parameter is not available in the following conditions: When Mode is set to 1 and Stage
is set to 4, 6, 8. 12 or 16; or when Mode is set to 2 and Stage is set to 4 or 10.
[2] VCM PHASER STEREO
The Color parameter is not available in the following conditions: When Mode is set to 1 and Stage
is set to 4, 6, or 8; or when Mode is set to 2 and Stage is set to 4 or 10.
No. Parameter Range Value Table No .
1 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
2 LFO Depth 0 – 127 (0 – 127)
3 Feedback Level -63 – +63 (1 – 127)
4 Delay Offset 0.0ms – 50.0ms (0 – 127) 2
5—
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 33.
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 EQ Mid Frequency (*2) 100Hz – 10.0kHz (14 – 54) 3
12 EQ Mid Gain (*2) -12dB – +12dB (52 – 76)
13 EQ Mid Width (*2) 0.1 – 12.0 (1 – 120)
14 —
15 Input Mode Mono, Stereo (0 – 1)
16 —
No. Parameter Range Value Table No .
1 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
2 LFO Depth 0 – 127 (0 – 127)
3 Delay Offset 0.0ms – 50.0ms (0 – 127) 2
4—
5—
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 33.
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 EQ Mid Frequency (*2) 100Hz – 10.0kHz (14 – 54) 3
12 EQ Mid Gain (*2) -12dB – +12dB (52 – 76)
13 EQ Mid Width (*2) 0.1 – 12.0 (1 – 120)
14 —
15 —
16 —
No. Parameter Range Value Table No .
1 Detune -50cent – +50cent (14 – 114)
2 Initial Delay Lch 0.0ms – 50.0ms (0 – 127) 2
3 Initial Delay Rch 0.0ms – 50.0ms (0 – 127) 2
4 Spread 0 – 63 (0 – 63)
5—
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 – 14: Same as the parameters shaded in gray in CROSS DELAY on page 33.
15 —
16 —
No. Parameter Range Value Table No .
1 Speed 0.040Hz – 10.00Hz (0 – 235) 17
2 Manual 0 – 127 (0 – 127)
3 Depth 0 – 127 (0 – 127)
4 Feedback 0 – 127 (0 – 127)
5 Type 1 – 3 (0 – 2)
6 Spread 0 – 127 (0 – 127)
7 Mix 0 – 127 (0 – 127)
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
2 LFO Depth 0 – 127 (0 – 127)
3 LFO Wave Triangle, Sine (0 – 1)
4 Delay Offset 0.09 – 36.21ms (0 – 139) 15
5 Feedback Level -100 – +100% (0 – 200)
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 33.
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 EQ Mid Frequency 100Hz – 10.0kHz (14 – 54) 3
12 EQ Mid Gain -12dB – +12dB (52 – 76)
13 EQ Mid Width 0.1 – 12.0 (1 – 120)
14 Modulation Phase -180 – +180 (0 – 16) 21
15 Feedback High Damp 0.1 – 1.0 (1 – 10)
16 Analog Feel 0 – 10 (0 – 10)
No. Parameter Range Value Table No.
1 LFO Speed 16th – 4thX16 (5 – 29) 12
2 LFO Depth 0 – 127 (0 – 127)
3 Feedback Level -63 – +63 (1 – 127)
4 Delay Offset 0.0ms – 50.0ms (0 – 127) 2
5 LFO Phase Reset Off (free run), Key On Reset,
SEQ Start Reset
(0 – 2)
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 33.
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 EQ Mid Frequency (*2) 100Hz – 10.0kHz (14 – 54) 3
12 EQ Mid Gain (*2) -12dB – +12dB (52 – 76)
13 EQ Mid Width (*2) 0.1 – 12.0 (1 – 120)
14 LFO Phase Difference -180deg – +180deg (4 – 124)
15 —
16 —
No. Parameter Range Value Table No.
1 Speed 0.100Hz – 10.00Hz (0 – 252) 18
2 Manual 0 – 127 (0 – 127)
3 Depth 0 – 127 (0 – 127)
4 Feedback 0 – 127 (0 – 127)
5 Stage 4, 6, 8, 10, 12, 16 (0 – 5)
6 Mode 1, 2, 3 (0 – 2)
7 Color 0 – 127 (0 – 127)
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 Speed 0.100Hz – 10.00Hz (0 – 252) 18
2 Manual 0 – 127 (0 – 127)
3 Depth 0 – 127 (0 – 127)
4 Feedback 0 – 127 (0 – 127)
5 Stage 4, 6, 8, 10 (0 – 3)
6 Mode 1, 2 (0 – 1)
7 Color 0 – 127 (0 – 127)
8 Spread 0 – 127 (0 – 127)
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —