Yamaha MX49 - Troubleshooting: Operation Errors; Arpeggio, Song, and Pattern Start Issues; Computer Communication and MIDI Data Issues; USB Save and Data Integrity Issues

MX49/MX61 Data List
39
Effect Parameter List
Category — MISC
[1] VCM EQ 501
[2] HARMONIC ENHANCER
[3] TALKING MODULATOR
[4] DAMPER RESONANCE
[5] PITCH CHANGE
[6] EARLY REFLECTION
[7] NOISE GATE + COMP + EQ
No. Parameter Range Value Table No .
1 EQ1 (LSH) Frequency 31.5Hz – 2.0kHz (12 – 84) 25
2 EQ1 (LSH) Gain -12.0dB – +12.0dB (60 – 300)
3 EQ2 Q 0.50 – 16.00 (0 – 60) 26
4 EQ2 Frequency 50.0 Hz – 20.0kHz (20 – 124) 25
5 EQ2 Gain -18.0dB – +18.0dB (0 – 360)
6 EQ3 Q 0.50 – 16.00 (0 – 60) 26
7 EQ3 Frequency 50.0 Hz – 20.0kHz (20 – 124) 25
8 EQ3 Gain -18.0dB – +18.0dB (0 – 360)
9 EQ4 Q 0.50 – 16.00 (0 – 60) 26
10 EQ4 Frequency 50.0 Hz – 20.0kHz (20 – 124) 25
11 EQ4 Gain -18.0dB – +18.0dB (0 – 360)
12 EQ5 (HSH) Frequency 500Hz – 20.0kHz (60 – 124) 21
13 EQ5 (HSH) Gain -12.0dB – +12.0dB (60 – 300)
14 Output Level -12.0dB – +12.0dB (60 – 300)
15 —
16 —
No. Parameter Range Value Table No .
1 HPF Cutoff Frequency 500Hz – 16.0kHz (28 – 58) 3
2 Drive 0 – 127 (0 – 127)
3 Mix Level 0 – 127 (0 – 127)
4—
5—
6—
7—
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No .
1 Vowel a, i, u, e, o (0 – 4)
2 Move Speed 1 – 62 (1 – 62)
3 Drive 0 – 127 (0 – 127)
4 Output Level 0 – 127 (0 – 127)
5—
6—
7—
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No .
1 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
2 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
3 EQ Low Frequency 32Hz – 2.0kHz (4 – 40) 3
4 EQ Low Gain -12 – +12dB (52 – 76)
5 High Damp 0.1 – 1.0 (1 – 10)
6 Pedal Response Slow, Normal, Fast (0 – 2)
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 —
14 —
15 —
16 Damper Control 0 – 127 (0 – 127)
No. Parameter Range Value Table No.
1 Pitch 1 -24 – +24 (40 – 88)
2 Fine 1 -50 – +50 (14 – 114)
3 Initial Delay 1 0.1ms – 400.0ms (0 – 127) 7
4 Feedback Level 1 -63 – +63 (1 – 127)
5 Pitch 2 -24 – +24 (40 – 88)
6 Fine 2 -50 – +50 (14 – 114)
7 Initial Delay 2 0.1ms – 400.0ms (0 – 127) 7
8 Feedback Level 2 -63 – +63 (1 – 127)
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Pan 1 L63 – C – R63 (1 – 127)
12 Output Level1 0 – 127 (0 – 127)
13 Pan 2 L63 – C – R63 (1 – 127)
14 Output Level2 0 – 127 (0 – 127)
15 —
16 —
No. Parameter Range Value Table No.
1 Type S-hall, L-hall, Random,
Reverse, Plate, Spring
(0 – 5)
2 Room Size 0.1 – 20.0 (0 – 127) 6
3 Diffusion 0 – 10 (0 – 10)
4 Initial Delay 0.1ms – 200.0ms (0 – 127) 5
5 Feedback Level -63 – +63 (1 – 127)
6 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Liveness 0 – 10 (0 – 10)
12 Density 0 – 3 (0 – 3)
13 Feedback High Damp 0.1 – 1.0 (1 – 10)
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 Comp Attack 1ms – 40ms (0 – 19) 8
2 Comp Release 10ms – 680ms (0 – 15) 9
3 Comp Threshold -48dB – -6dB (79 – 121)
4 Comp Ratio 1.0 – 20.0 (0 – 7) 10
5 Comp Output Level 0 – 127 (0 – 127)
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 33.
10 —
11 Noise Gate Attack 1ms – 40ms (0 – 19)
12 Noise Gate Release 10ms – 680ms (0 – 15)
13 Noise Gate Threshold -73dB – -30dB (54 – 97)
14 EQ Mid Frequency 100Hz – 10.0kHz (14 – 54) 3
15 EQ Mid Gain -12dB – +12dB (52 – 76)
16 EQ Mid Width 0.1 – 12.0 (1 – 120)