Yamaha RX-V2700 User Manual (English)

Other manuals for Yamaha RX-V2700

Questions and Answers:

R
roy05Aug 23, 2025
Why does my Yamaha RX-V2700 Receiver fail to turn on or enter standby mode?
- P
  Peter HubbardAug 23, 2025
  If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, it could be due to several reasons: * Ensure the power cable is firmly connected. * Verify that the speaker impedance setting matches your speakers. * Check speaker wire connections for security and ensure no wires are touching other than their respective connections, as the protection circuitry might be activated. * If the unit experienced a strong electric shock, set it to standby, disconnect the power cable, wait 30 seconds, and then reconnect it.
C
christophercarterSep 1, 2025
What to do if Yamaha RX-V2700 Receiver suddenly enters standby mode?
- P
  porterdanielSep 2, 2025
  If your Yamaha Receiver suddenly enters standby mode, it's likely because the internal temperature has become too high, activating the overheat protection circuitry. To resolve this, wait about 1 hour for the unit to cool down before turning it back on.
E
Edgar MataSep 1, 2025
Why is there no sound from the surround speakers on my Yamaha Receiver?
- P
  paulloriSep 1, 2025
  If you are not hearing sound from the surround speakers on your Yamaha Receiver, and the unit is in 'STRAIGHT' mode while playing a monaural source, press the STRAIGHT button on the front panel to disable 'STRAIGHT' mode.
J
John HuntAug 30, 2025
Why is there no sound from the center speaker on my Yamaha RX-V2700?
- R
  rellisAug 30, 2025
  If you are not hearing sound from the center speaker on your Yamaha Receiver, it might be because you are using a source or program combination that does not output sound from all channels. In the settings, set 'Center' to either 'Small' or 'Large'.
A
Anna HubbardAug 29, 2025
Why is the volume low when playing records on my Yamaha Receiver?
- N
  nperezAug 29, 2025
  If the volume level is low when playing a record on your Yamaha Receiver, ensure the turntable is connected to the GND terminal. If using a turntable with an MC cartridge, connect it through an MC head amplifier. Also, check if the component connected to the AUDIO OUT (REC) jacks of this unit is turned off, and turn it on if necessary.
G
Grace SnyderAug 28, 2025
Why are my Yamaha RX-V2700 surround back speakers not working?
- S
  sabrina76Aug 28, 2025
  If you're not getting any sound from the surround back speakers on your Yamaha Receiver: * If “Surround” in “Speaker Set” is set to “None”, then “Surround Back” is automatically set to “None”. * If “Surround Back” in “Speaker Set” is set to “None”, set “Surround Back” to a setting other than “None”. * Ensure the connected component is set to output Dolby Digital or DTS digital signals by following the operating instructions for your component. * If Audio input jack select is set to “ANALOG”, set it to “AUTO”.
J
Jessica FoleyAug 27, 2025
What causes the sound to suddenly go off on my Yamaha RX-V2700?
- R
  Raymond CarrollAug 27, 2025
  If the sound suddenly goes off on your Yamaha Receiver, it might be due to the activation of the protection circuitry because of a short circuit. Check that the speaker impedance setting is correct and ensure that the speaker wires are not touching each other, then turn the unit back on.
K
keithmorrowAug 25, 2025
Why is there no sound from my Yamaha RX-V2700 Receiver?
- A
  Anne WilsonAug 26, 2025
  If your Yamaha Receiver has no sound, check that all input and output cables are properly connected and not defective. Ensure the optimizer microphone is disconnected. Verify that 'Audio input jack select' is set to 'AUTO'. If set to 'ANALOG' while playing Dolby Digital or DTS, select an appropriate input source. Also, make sure the volume isn't turned down or muted. Finally, ensure the source signals can be reproduced by the unit.
J
jeffrey16Aug 25, 2025
How to troubleshoot no sound on Yamaha RX-V2700 Receiver?
- J
  Justin WalkerAug 25, 2025
  If there is no sound coming from your Yamaha Receiver, consider the following: * Check and properly connect all input and output cables. If the issue continues, the cables might be defective. * Disconnect the optimizer microphone. * Ensure the Audio input jack select is set to “AUTO”. * If playing a Dolby Digital or DTS source, avoid setting Audio input jack select to “ANALOG”. Instead, select the appropriate input source using the INPUT selector. * Make sure the volume isn't too low and that the receiver isn't muted. Adjust the volume and press MUTE to resume audio output. * Confirm that the input signals are reproducible by the unit. Finally, note that HDMI components might need to support HDCP copy protection standards.

Yamaha RX-V2700 Specifications

General

Channels	7.1
Total Harmonic Distortion (THD)	0.04%
HDMI outputs	1
Signal to noise ratio	100 dB
Frequency Response	10Hz - 100kHz
Audio Formats Supported	Dolby Digital, Dolby Digital EX, DTS, DTS-ES, Dolby Pro Logic IIx, DTS 96/24
Tuning range	FM, AM
Input sensitivity	200mV
Digital inputs	3 x coaxial
Video Connections	Component, Composite, S-Video
Video Inputs	Component: 3
Video Outputs	Component: 1
Audio Inputs	7.1 channel input
Audio Outputs	7.1 channel pre-out, 2 x RCA
Power Output (8 ohms)	140 W (8 ohms, 20 Hz - 20 kHz, 0.04% THD)