To Next PageTo Next PageWhy is bass reproduction poor on my Yamaha RX-V350 Receiver?
If you're experiencing poor bass reproduction with your Yamaha Receiver, and “SOUND 1D BASS” on the set menu is set to SWFR or BOTH but your system doesn't have a subwoofer, select FRONT. Also, if the speaker mode settings on the set menu don't match your speaker configuration, select the appropriate position for each speaker based on their size.
What to do if the sound suddenly goes off on my Yamaha Receiver?
If the sound on your Yamaha Receiver suddenly cuts out, it could be due to a few reasons. The protection circuitry might have been activated because of a short circuit. Check that the speaker wires are not touching each other, and then turn the unit back on. Alternatively, the sleep timer might have turned the unit off. In this case, turn the power back on and play the source again. Finally, ensure the sound isn't muted by pressing the MUTE button.
How to fix Yamaha RX-V350 remote control that is not working?
If your Yamaha Receiver's remote control isn't working properly, consider these potential solutions. Ensure you are within a maximum range of 6 m (20 feet) and no more than 30 degrees off-axis from the front panel. Reposition the unit if direct sunlight or lighting is interfering with the remote control sensor. Replace all batteries if they are weak. Also, verify that the manufacture code has been set correctly, and try setting another code of the same manufacturer.
Why is there no sound from my Yamaha RX-V350?
If you're experiencing no sound from your Yamaha Receiver, start by checking all input and output cable connections to ensure they are properly connected; if the problem persists, the cables may be defective. Next, verify that you've selected the correct input source using INPUT l / h or 6CH INPUT (or the input selector buttons). Also, make sure the speaker connections are secure and that the proper front speakers are selected with SPEAKERS A/ B/OFF. Don't forget to check the volume level and ensure the unit isn't muted by pressing MUTE or any operation buttons. Finally, confirm that the source you're playing is compatible with the receiver.
Why does the remote control not work with my Yamaha RX-V350?
If the remote control for your Yamaha Receiver isn't working properly, make sure you're within a maximum range of 6 meters (20 feet) and no more than 30 degrees off-axis from the front panel. Also, reposition the unit if direct sunlight or lighting is striking the remote control sensor. Finally, replace all batteries if they are weak.
How to tune into the desired station on Yamaha RX-V350 Receiver?
If you cannot tune into the desired station with the automatic tuning method on your Yamaha Receiver, it may be because the signal is weak or the antenna connections are loose. Tighten the AM loop antenna connections and orient it for best reception.
How to stop a humming sound from my Yamaha RX-V350?
If you hear a humming sound from your Yamaha Receiver, it could be due to incorrect cable connections. Firmly connect the audio plugs. If the problem persists, the cables may be defective.
Why is there no sound from the surround speakers on my Yamaha Receiver?
If you're not getting any sound from the surround speakers on your Yamaha Receiver, start by checking that the output level of the surround speakers isn't set to minimum. If it is, raise the output level. Also, if you're playing a monaural source with program 9, try selecting another sound field program.
What to do if Yamaha RX-V350 Receiver fails to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, there are several potential causes. First, ensure the power cord is securely connected. If that's not the issue, the protection circuitry might be activated; in this case, check all speaker wire connections to make sure they are secure and not touching anything else. Finally, if the unit has been exposed to a strong electric shock, try setting it to standby mode, disconnecting the power cord for 30 seconds, and then plugging it back in.
What does 'CHECK SP WIRES' mean on Yamaha RX-V350 Receiver?
If you see “CHECK SP WIRES” on the front panel display of your Yamaha Receiver, it indicates that the speaker cables are short-circuited. To fix this, make sure all speaker cables are connected correctly.
General| Channels | 5.1 |
|---|---|
| Dolby Digital | Yes |
| DTS | Yes |
| FM/AM Tuner | Yes |
| Impedance | 6 ohms |
| Type | AV Receiver |
| Input Sensitivity | 200 mV |
| Signal-To-Noise Ratio | 100 dB |
| Total Harmonic Distortion | 0.06% |
| Frequency Response | 10Hz - 100kHz |
| Amplifier Type | Discrete |
| Power Output | 100W per channel |
| Outputs | 1 x Audio, 1 x Video |
| Surround Sound Formats | Dolby Digital, Dolby Pro Logic II, DTS |
| Input Impedance | 47 kOhms |
| Audio Inputs/Outputs | RCA |
| Digital Audio Inputs | 2 (1 x Optical, 1 x Coaxial) |
| Video Inputs/Outputs | Composite |
