To Next PageTo Next PageWhy is a humming sound heard from my Yamaha RX-V3800?
If you hear a humming sound from your Yamaha Receiver, it could be due to: * Loose audio cable connections. Ensure the audio cables are firmly connected. If the problem persists, the cables may be defective. * Missing turntable ground connection. Connect the grounding cable of the turntable to the GND terminal of this unit.
Why is there no sound coming from my Yamaha RX-V3800 Receiver?
If you're experiencing no sound from your Yamaha Receiver, there could be several reasons: * Check if the input or output cables are connected properly. If the problem continues, the cables might be defective. * Ensure the audio input jack select is set to “AUTO”. * If set to “ANALOG”, and your source outputs digital signals, select the appropriate input source using the CINPUT selector on the front panel or the input selector buttons on the remote. * Make sure the volume isn't turned down or muted. Adjust the volume and check the mute setting. * The connected HDMI components must support the HDCP copy protection standards. * If “Support Audio” is set to “Other”, change it to the appropriate option.
How to eliminate buzzing and whining noises from Yamaha Receiver?
To resolve buzzing and whining noises from your Yamaha Receiver, move the unit away from the TV set.
How to stop a humming sound from my Yamaha RX-V3800 Receiver?
To address a humming sound coming from your Yamaha Receiver, ensure the audio cables are firmly connected. If the problem persists, the cables may be defective.
How to fix noisy FM stereo reception on Yamaha RX-V3800?
If you're experiencing noisy FM stereo reception on your Yamaha Receiver, check the antenna connections. The issue may also be due to the characteristics of FM stereo broadcasts when the transmitter is too far away or the antenna input is poor.
Why is no sound heard from the presence speakers of my Yamaha Receiver?
If you're not hearing sound from the presence speakers connected to your Yamaha Receiver, the sound field programs might be turned off. Press PSTRAIGHT to turn them on.
Why is no sound heard from the subwoofer of my Yamaha RX-V3800 Receiver?
If you're not getting any sound from the subwoofer connected to your Yamaha Receiver, and a Dolby Digital or DTS signal is being played, check that “Bass Out” in “Speaker Set” is set to “SWFR” or adjust as needed.
Why is no sound heard from the surround speakers of my Yamaha Receiver?
If you're not hearing sound from the surround speakers on your Yamaha Receiver, it could be that the unit is in “STRAIGHT” mode while playing a monaural source. Press PSTRAIGHT on the front panel so that “STRAIGHT” disappears from the front panel display.
Why is no sound heard from the center speaker of my Yamaha Receiver?
If you're not hearing sound from the center speaker of your Yamaha Receiver, it might be because you are using a source or program combination that does not output sound from all channels. Set “Center” to “Small” or “Large.
Why is my Yamaha Receiver remote control not working?
If the remote control for your Yamaha Receiver isn't working properly, replace the batteries. Also, make sure the remote controls are placed at the proper distance from the unit.
General| Audio Channels | 7.1 |
|---|---|
| Amplifier Type | Discrete |
| THD (Total Harmonic Distortion) | 0.04% |
| Signal-to-Noise Ratio | 100 dB |
| HDMI Inputs | 4 |
| HDMI Outputs | 2 |
| HDMI Version | 1.3a |
| Dolby Digital | Yes |
| DTS | Yes |
| Surround Sound | Yes |
| Component Video Input | 3 |
| Component Video Output | 1 |
| S-Video Input | 4 |
| S-Video Output | 1 |
| Composite Video Input | 5 |
| Composite Video Output | 1 |
| Digital Audio Input (Coaxial) | 3 |
| Analog Audio Input | 6 |
| Weight | 37.5 lbs |
| Input Sensitivity | 200 mV |
| Power Output | 140 Watts (8 ohms, 20 Hz - 20 kHz, 0.04% THD, 2 channels driven) |
| Frequency Response | 10 Hz - 100 kHz |
Layout of the Digital Signal Processor Printed Circuit Board on Side A.
List of electrical components with warnings and special characteristics.
Settings for speaker impedance, remote sensor, and RS-232C.
