Yealink SIP-T53W Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
303
Default
0
Parameter
sip.skip_redundant_failover_addr <y0000000000xx>.cfg
Description
It enables or disables the phone only to send requests to the servers with different IP addresses when
encountering a failover.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Parameter
account.X.sip_server.Y.expires
[1][2]
<MAC>.cfg
Description
It configures the registration expiration time (in seconds) of SIP server Y for a specific account.
Permitted
Values
Integer from 30 to 2147483647
Default
3600
Web UI
Account > Register > SIP Server Y > Server Expires
Parameter
account.X.sip_server.Y.retry_counts
[1][2]
<MAC>.cfg
Description
It configures the retry times for the phone to resend requests when the SIP server Y is unavailable or
there is no response from the SIP server Y.
The phone moves to the next available server after three failed attempts.
Permitted
Values
Integer from 0 to 20
Default
3
Web UI
Account > Register > SIP Server Y > Server Retry Counts
Parameter
account.X.sip_server.Y.only_signal_with_registered
[1][2]
<MAC>.cfg
Description
It enables or disables the phone to only send requests to the registered server when encountering a
failover.
Note: It works only if “account.X.sip_server.Y.register_on_enable” is set to 1 (Enabled) and “accoun-
t.X.sip_server.Y.failback_mode” is set to 1, 2 or 3.
Permitted
Values
0-Disabled
1-Enabled
Default
0
Parameter
account.X.sip_server.Y.invite_retry_counts
[1][2]
<MAC>.cfg
Description
It configures the number of retries attempted before sending requests to the next available server
when encountering a failover.
Permitted
Values
Integer from 1 to 10
Default
3
Parameter
account.X.sip_server.Y.failback_mode
[1][2]
<MAC>.cfg
Description
It configures the mode for the phone to retry the primary server in failover.
Note: It works only if “account.X.sip_server.Y.address” is set to the domain name of the SIP server.
Permitted
Values
0-newRequests: all requests are sent to the primary server first, regardless of the last server that was
used.
1-DNSTTL: the phone will send requests to the last registered server first. If the time defined by

Yealink SIP-T53W Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP mobile phone
Product color	Gray
Keypad illumination	Yes
Wi-Fi standards	802.11a, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version	4.2
Security algorithms	AES, HTTPS, SIPS
Networking standards	IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP/TFTP/HTTP/HTTPS
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Lines quantity	8 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	12
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Power consumption (typical)	2.3 W
Volume control	Buttons
Number of programmable keys	8
Storage temperature (T-T)	-30 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	3.7 \
Display resolution	360 x 160 pixels
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Number of DECT wireless handsets	4
Voice codecs	G.722, G.723.1, G.726, G.729A, G.729B, OPUS, iLBC

Weight and Dimensions

Depth	210.6 mm
Width	212 mm
Height	174.5 mm