Yealink SIP-T53W Administrator's Guide

Call Features
368
3-DNS-NAPTR
Default
0
Parameter
dialplan.emergency.X.value
[2]
<y0000000000xx>.cfg
Description
It configures the emergency number to use on your phones so a caller can contact emergency ser-
vices in the local area when required.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is not set to HELD.
Permitted
Values
Number or SIP URI
Default
When X = 1, the default value is 911;
When X = 2-255, the default value is Blank.
Parameter
dialplan.emergency.X.server_priority
[2]
<y0000000000xx>.cfg
Description
It configures the priority of which the emergency servers to be used first.
Multiple values are separated by commas. The servers to be used in the order listed (left to right).
The IP phone tries to make emergency calls using the emergency server with higher priority, and then
with lower priority. The IP phone tries to send the INVITE request to each emergency server three
times.
Note: If the account information has been configured (no matter whether the account registration suc-
ceeds or fails), the emergency calls will be dialed using the following priority: SIP server > emergency
server; if not, the emergency server will be used. It works only if “dialplan.emergency.enable” is set to
1 (Enabled). And “dialplan.emergency.asserted_id_source” is not set to HELD.
Permitted
Values
a combination of digits 1, 2 and 3
Default
1, 2, 3
Parameter
dialplan.emergency.held.server_url <y0000000000xx>.cfg
Description
It configures the primary Location Information Server URL for the phone to send HELD location
request.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is set to HELD.
Permitted
Values
String
Default
Blank
Parameter
dialplan.emergency.held.secondary.server_url <y0000000000xx>.cfg
Description
It configures the secondary Location Information Server URL for the phone to send HELD location
request.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is set to HELD.
Permitted
Values
String
Default
Blank
Supported
Devices
All phones except T48G, T46G, T42G, T41P and T29G
Parameter
dialplan.emergency.held.request_type <y0000000000xx>.cfg

Yealink SIP-T53W Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP mobile phone
Product color	Gray
Keypad illumination	Yes
Wi-Fi standards	802.11a, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version	4.2
Security algorithms	AES, HTTPS, SIPS
Networking standards	IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP/TFTP/HTTP/HTTPS
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Lines quantity	8 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	12
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Power consumption (typical)	2.3 W
Volume control	Buttons
Number of programmable keys	8
Storage temperature (T-T)	-30 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	3.7 \
Display resolution	360 x 160 pixels
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Number of DECT wireless handsets	4
Voice codecs	G.722, G.723.1, G.726, G.729A, G.729B, OPUS, iLBC

Weight and Dimensions

Depth	210.6 mm
Width	212 mm
Height	174.5 mm