YOKOGAWA ADMAG AXG015

User’s
Manual
Contents
1. Introduction
1.1 For Safe Use of Product ................................................1
1.2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Combination for Remote Sensor and
Remote Transmitter ..... .... .... .... .... .... .... .... ..................... .3
2. Receiving and Storage
2.1 Model and Speci cations Check .. .. . .. .. .. .. . .. .. .. .. . .. .. .. .. . .. .. .. .. . .. .. 4
2.2 Storage Precautions ... ... ....... ... .... ... ....... ... ....... ... .... ... ....4
3. Installation
4. Wiring
4.1 Wiring Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2.5 Recommended Cable for EtherNet/IP
communication ....... .... ....... .... .... ....... .... ....... .... .6
4.3 Cable Entries .................................................................6
4.4 Connecting to External Products of Integral
Flowmeter and Remote Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.4.1 Wiring Precautions for Power Supply Cables ..6
4.4.2 DC Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.4.3 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.4.4 Connecting to External Products . . . . . . . . . . . . . . . . . . . . . . 7
4.4.5 Wiring Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Basic Operating Procedures
5.1 Operation by Display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2 Display and Basic Con guration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.3 Display Mode and Setting Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.4 Parameter Setting from Display Panel ....................... 10
5.5 microSD Card Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.6 BRAIN Con guration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.7 HART Con guration Tool . .. . .. . . .. . .. . . .. . . .. . .. . . .. . .. . . .. . .. . . .. . . 10
5.8 Modbus Con guration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.9 FOUNDATION  eldbus Con guration Tool . . . . . . . . . . . . . . . . . . . . . . 11
5.10 EtherNet/IP Con guration Tool ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. .. .. 11
6. Operation
6.1 Pre-operation Zero Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.2 Zero Adjustment from Display Unit . .. . .. . .. . .. . .. . .. . .. . .. . .. .. 12
6.3 Hardware Switch Setting ............................................ 12
6.3.1 Integral Type and AXG4A Remote
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.3.2 AXG1A Remote Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.3.3 AXFA11 Remote Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . 13
7. Errors and Countermeasures (Display unit)
ADMAG TI Series
AXG Magnetic Flowmeter
EtherNet/IP Communication Type
Installation Manual
Difference to IM 01E22A01-01EN
IM 01E21A01-03EN-A
IM 01E21A01-03EN-A
1st Edition
Integral Flowmeter
This manual outlines the basic guidelines for installation
and wiring procedures. This manual is applicable only for
EtherNet/IP communication type. For the items which are
not covered in this manual, read the user’s manuals and the
general speci cations as listed in Table 1.1.
Remote Transmitter
Please read the following descriptions in conjunction with IM 01E22A01-01EN.
This document only applies to AXG produced at Yokogawa Corporation of America and sold to North/Central America.
AXG Magnetic Flowmeter

YOKOGAWA ADMAG AXG015 Specifications

General

Type	Electromagnetic Flowmeter
Model	ADMAG AXG015
Category	Measuring Instruments
Measurement Principle	Faraday's law of electromagnetic induction
Nominal Size	15 mm
Measurement Range	0.1 to 10 m/s
Protection Grade/Rating	IP67, NEMA 4X
Material	Stainless Steel
Communication	HART
Output Signal	4 to 20 mA
Power Supply	24 V DC
Process Connection	Flanged
Lining Material	PTFE
Electrode Material	316L Stainless Steel
Repeatability	±0.1% of rate

Summary

Introduction

For Safe Use of Product

Essential safety guidelines and precautions for product operation and handling.

Warranty

Information regarding the warranty terms and conditions for the product.

Combination for Remote Sensor and Remote Transmitter

Details on compatible combinations of remote sensors and transmitters.

Receiving and Storage

Model and Specifications Check

Verifying product model, suffix code, serial number, and specifications against order.

Storage Precautions

Guidelines for proper storage to maintain product integrity before installation.

Installation

Wiring

Wiring Precautions

Essential guidelines and warnings for safe and correct wiring procedures.

Cables

Details on cable types and specifications, including Ethernet cables.

Cable Entries

Information regarding the proper use of cable entries for secure connections.

Wiring Precautions for Power Supply Cables

Specific safety warnings and precautions for connecting power supply cables.

Terminal Configuration Integral Flowmeter and AXG4 A Transmitter

Diagram and explanation of terminal layouts for integral and remote transmitters.

Wiring Procedure for Ethernet communication cable

Step-by-step instructions for connecting Ethernet communication cables.

Terminal Configuration AXG4 A Remote Transmitter

Specific terminal layout for the AXG4A remote transmitter.

Basic Operating Procedures

Display Mode and Setting Mode

How to navigate between display and setting modes for parameter configuration.

Parameter Setting from Display Panel

Procedures for setting parameters using the device's display panel.

EtherNetIP Configuration Tool

Details on configuring EtherNet/IP settings, including EDS files and supported software.

Operation

Hardware Switch Setting

Guide to configuring hardware switches for IP address, write protection, and DHCP.

Setting of Write Protect Switch

Instructions on using the write protect switch to prevent parameter overwriting.

Setting of Address Switch (ADDRESS)

Details on configuring the device IP address using the address switch.

Setting Enable Hardware Address Switch (SW3-1)

How to enable or disable the hardware address switch and DHCP switch.

Setting DHCP Switch (SW3-2)

Instructions for enabling or disabling the DHCP function via the switch.

Errors and Countermeasures

System Alarm

Table of system alarms, error descriptions, and recommended countermeasures.