York Fitness Pacer 5000 HRC User Manual (English)

Questions and Answers:

J
joshuajonesAug 13, 2025
What to do if York Fitness Treadmill shows Error 2 (Over speed error)?
- C
  ccollinsAug 13, 2025
  If your York Fitness Treadmill displays Error 2, which indicates an over-speed error, it could be due to several reasons: * The actual belt speed is faster than the speed displayed on the console. * The mat moved before the motor moved. * The user is pushing hard on the running mat, causing it to run faster than the displayed speed. * The controller is damaged, and the motor is running out of control. To resolve this, simply turn the power off and on again to reset the treadmill. However, if the controller is damaged, call your dealer for service and do not use the treadmill until it is repaired.
L
Laura RodriguezAug 17, 2025
What to do if York Fitness Treadmill shows Error 3 (Safety key error)?
- M
  Misty BennettAug 17, 2025
  If your York Fitness Treadmill displays Error 3, it indicates a safety key error. This means the safety key is not making proper contact with the console. Ensure the safety key is correctly and securely attached to the console.
J
Jeffrey SmithAug 20, 2025
What to do if York Fitness Pacer 5000 HRC will not start?
- A
  Amanda CunninghamAug 21, 2025
  If your York Fitness Treadmill won't start, here's what to check: 1. Ensure the treadmill is plugged into a grounded outlet. 2. Make sure the safety key is properly inserted into the console. 3. Check your house circuit breaker and reset or replace the fuse if necessary. 4. Examine the treadmill's circuit breaker and reset it. If it trips again, lubricate the deck to reduce friction. 5. Verify the On/Off switch is in the "ON" position.
J
johnmartinAug 25, 2025
Why does my York Fitness Treadmill running belt slip?
- J
  Justin EvansAug 25, 2025
  If the running belt on your York Fitness Treadmill is slipping, it could be due to the following reasons: 1. The running mat might not be tight enough. 2. The drive belt may not be tight enough. To resolve this, adjust the running mat tension and the drive belt tension accordingly.
L
lisaleeAug 28, 2025
What to do if York Fitness Pacer 5000 HRC Treadmill shows Error 11 (Communication error)?
- R
  Rachel MahoneyAug 28, 2025
  If your York Fitness Treadmill displays Error 11, indicating a communication error, it means the communication between the console and the controller is not functioning properly. Check the communication line connections to ensure they are not loose or the cables are not pinched. If the communication cable is damaged, replace it. Then, turn the power off and on again to reset the treadmill.
M
Melissa DaughertySep 1, 2025
How to fix York Fitness Pacer 5000 HRC Treadmill running belt off center?
- W
  Wendy VazquezSep 1, 2025
  If the running belt on your York Fitness Treadmill is off-center, it's likely because the running mat tension is uneven across the rear roller. To fix this, center the running mat.
J
John MurraySep 5, 2025
Why does my York Fitness Treadmill running belt hesitate when stepped on?
- B
  brentnewmanSep 5, 2025
  If the running belt on your York Fitness Treadmill hesitates when you step on it, it could be due to: 1. Insufficient lubrication. 2. The running mat being either too tight or too loose. To resolve this, apply silicone lubricant and adjust the running mat tension.
G
gutierrezjodySep 8, 2025
What does Error 5 mean on York Fitness Treadmill?
- P
  paulapalmerSep 9, 2025
  Error 5 on your York Fitness Treadmill indicates an incline motor error, meaning the incline motor is not functioning properly. You can wait until the incline motor has returned to normal temperature, then try again. It can also be caused by: sensor connection cable problem, defective or damaged sensor (Potentiometer), or damaged incline motor.