EasyManua.ls Logo

York 13 Seer-YCJD - User Manual

York 13 Seer-YCJD
16 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Johnson Controls Unitary Products 835964-UIM-A-0112
R-410A
OUTDOOR SPLIT-SYSTEM
AIR CONDITIONING
MODELS: 13 & 14.5 SEER -
TCG(D,F)/GCGD/TCJ(D,F)/YCJ(D,F) SERIES
1.5 TO 5 TONS – 1 & 3 PHASE
INSTALLATION MANUAL
®
LIST OF SECTIONS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‘1
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
UNIT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
ORIFICE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TXV INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
EVACUATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SYSTEM CHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INSTRUCTING THE OWNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LIST OF FIGURES
Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation of Vapor Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Underground Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Heat Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Orifice Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Outdoor Unit Control Box (Single Phase) . . . . . . . . . . . . . . . . . . . . . .7
Outdoor Unit Control Box (Three Phase) . . . . . . . . . . . . . . . . . . . . . . .7
Typical Field Wiring (Air Handler / Electrical Heat) (Single-Phase) . . .8
Typical Field Wiring (Air Handler / Electrical Heat) (Three-Phase) . . . 8
Thermostat Chart - Single Stage AC with PSC Air Handler . . . . . . . . 9
Thermostat Chart - Single Stage AC with PSC Air Handler . . . . . . . 10
Thermostat Chart - Single Stage AC with PSC Furnace . . . . . . . . . 11
Thermostat Chart - Single Stage AC with PSC Furnace . . . . . . . . . 12
Wiring Diagram - Single Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Wiring Diagram - Three Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LIST OF TABLES
Application Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 R-410A Saturation Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION I: GENERAL
The outdoor units are designed to be connected to a matching indoor
coil with sweat connect lines. Sweat connect units are factory charged
with refrigerant for a matching indoor coil plus 15 feet of field-supplied
lines.
The refrigerant charge may need to be changed for some indoor-out-
door unit combinations, elevation differences or total line lengths. Refer
to Application Data covering “General Piping Recommendations and
Refrigerant Line Length” (Part Number 247077).
SECTION II: SAFETY
This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.
Understand and pay particular attention to the signal words DANGER,
WARNING, or CAUTION.
DANGER indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury
.
WARNING indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury
.
CAUTION indicates a potentially hazardous situation, which, if not
avoided may result in minor or moderate injury
. It is also used to
alert against unsafe practices and hazards involving only property dam-
age.
INSPECTION
As soon as a unit is received, it should be inspected for possible dam-
age during transit. If damage is evident, the extent of the damage
should be noted on the carrier’s delivery receipt. A separate request for
inspection by the carrier’s agent should be made in writing. See Local
Distributor for more information.
Requirements For Installing/Servicing R-410A Equipment
Gauge sets, hoses, refrigerant containers, and recovery system
must be designed to handle the POE type oils, and the higher
pressures of R-410A.
Manifold sets should be high side and low side with low side
retard.
All hoses must have a 700 psig service pressure rating.
Leak detectors should be designed to detect HFC refrigerant.
Recovery equipment (including refrigerant recovery containers)
must be specifically designed to handle R-410A.
Do not use an R-22 TXV.
A liquid-line filter drier is required on every unit.
This product must be installed in strict compliance with the
enclosed installation instructions and any applicable local, state,
and national codes including, but not limited to building, electrical,
and mechanical codes.
R-410A systems operate at higher pressures than R-22 systems.
Do not use R-22 service equipment or components on R-410A
equipment. Service equipment
Must Be Rated for R-410A.
Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.
Improper installation, adjustment, alteration, service or mainte-
nance can cause injury or property damage. Refer to this manual
for assistance or for additional information, consult a qualified con-
tractor, installer or service agency.
Question and Answer IconNeed help?

Do you have a question about the York 13 Seer-YCJD and is the answer not in the manual?

Summary

SECTION I: GENERAL

SECTION II: SAFETY

INSPECTION

Check for possible damage during transit and note any damage on the carrier's delivery receipt.

Requirements For Installing;Servicing R-410 A Equipment

Gauge sets, hoses, and recovery equipment must handle POE oils and higher pressures of R-410A.

LIMITATIONS

TABLE 1: Application Limitations

Lists minimum and maximum ambient and coil temperatures for operation.

Maximum allowable line length

Specifies the maximum permitted length for refrigerant lines.

SECTION III: UNIT INSTALLATION

LOCATION

Guidelines for selecting and checking the suitability of the installation site for outdoor units.

ADD-ON REPLACEMENT;RETROFIT

Steps for replacing an R-22 unit with an R-410A unit, including line-set replacement.

GROUND INSTALLATION

Instructions for installing the unit on a solid base, considering clearances and sound transmission.

ROOF INSTALLATION

Considerations for supporting the unit's total weight and minimizing sound transmission on a roof.

LIQUID LINE FILTER-DRIER

Location and importance of using the correct replacement for the liquid line filter-drier.

PRECAUTIONS DURING LINE INSTALLATION

Key steps and warnings for installing refrigerant lines to prevent damage and ensure system integrity.

PRECAUTIONS DURING BRAZING OF LINES

PRECAUTIONS DURING BRAZING SERVICE VALVE

SECTION IV: ORIFICE INSTALLATION

Install Schrader Valve Core and Orifice

Steps for installing the Schrader Valve Core and Orifice into the distributor assembly.

SECTION V: TXV INSTALLATION

SECTION VI: EVACUATION

SECTION VII: SYSTEM CHARGE

SUPERHEAT CHARGING METHOD - PISTON INDOOR

Procedure to charge the system using superheat for indoor units with pistons.

SUBCOOLING CHARGING METHOD - TXV INDOOR

Procedure to charge the system using subcooling for indoor units with TXVs.

SECTION VIII: ELECTRICAL CONNECTIONS

GENERAL INFORMATION & GROUNDING

Checking electrical supply, power wiring, control wiring, and grounding requirements.

FIELD CONNECTIONS POWER WIRING

Steps for installing the disconnect switch, running power wiring, and making connections.

FIELD CONNECTIONS CONTROL WIRING

Thermostat Chart - Single Stage AC with PSC Air Handler

Thermostat Chart - Single Stage AC with PSC Air Handler

Thermostat Chart - Single Stage AC with PSC Furnace

Thermostat Chart - Single Stage AC with PSC Furnace

SECTION IX: INSTRUCTING THE OWNER

MAINTENANCE

Guidelines for cleaning outdoor coils, fan motors, and indoor components.

SECTION X: WIRING DIAGRAM

Wiring Diagram - Three Phase

Summary

SECTION I: GENERAL

SECTION II: SAFETY

INSPECTION

Check for possible damage during transit and note any damage on the carrier's delivery receipt.

Requirements For Installing;Servicing R-410 A Equipment

Gauge sets, hoses, and recovery equipment must handle POE oils and higher pressures of R-410A.

LIMITATIONS

TABLE 1: Application Limitations

Lists minimum and maximum ambient and coil temperatures for operation.

Maximum allowable line length

Specifies the maximum permitted length for refrigerant lines.

SECTION III: UNIT INSTALLATION

LOCATION

Guidelines for selecting and checking the suitability of the installation site for outdoor units.

ADD-ON REPLACEMENT;RETROFIT

Steps for replacing an R-22 unit with an R-410A unit, including line-set replacement.

GROUND INSTALLATION

Instructions for installing the unit on a solid base, considering clearances and sound transmission.

ROOF INSTALLATION

Considerations for supporting the unit's total weight and minimizing sound transmission on a roof.

LIQUID LINE FILTER-DRIER

Location and importance of using the correct replacement for the liquid line filter-drier.

PRECAUTIONS DURING LINE INSTALLATION

Key steps and warnings for installing refrigerant lines to prevent damage and ensure system integrity.

PRECAUTIONS DURING BRAZING OF LINES

PRECAUTIONS DURING BRAZING SERVICE VALVE

SECTION IV: ORIFICE INSTALLATION

Install Schrader Valve Core and Orifice

Steps for installing the Schrader Valve Core and Orifice into the distributor assembly.

SECTION V: TXV INSTALLATION

SECTION VI: EVACUATION

SECTION VII: SYSTEM CHARGE

SUPERHEAT CHARGING METHOD - PISTON INDOOR

Procedure to charge the system using superheat for indoor units with pistons.

SUBCOOLING CHARGING METHOD - TXV INDOOR

Procedure to charge the system using subcooling for indoor units with TXVs.

SECTION VIII: ELECTRICAL CONNECTIONS

GENERAL INFORMATION & GROUNDING

Checking electrical supply, power wiring, control wiring, and grounding requirements.

FIELD CONNECTIONS POWER WIRING

Steps for installing the disconnect switch, running power wiring, and making connections.

FIELD CONNECTIONS CONTROL WIRING

Thermostat Chart - Single Stage AC with PSC Air Handler

Thermostat Chart - Single Stage AC with PSC Air Handler

Thermostat Chart - Single Stage AC with PSC Furnace

Thermostat Chart - Single Stage AC with PSC Furnace

SECTION IX: INSTRUCTING THE OWNER

MAINTENANCE

Guidelines for cleaning outdoor coils, fan motors, and indoor components.

SECTION X: WIRING DIAGRAM

Wiring Diagram - Three Phase

York 13 Seer-YCJD Specifications

General IconGeneral
BrandYork
Model13 Seer-YCJD
CategoryAir Conditioner
LanguageEnglish

Related product manuals