York B1HA036A06 - User Manual

GENERAL
YORK Model B1HA units are factory assembled heat pumps
designed for outdoor installation on a rooftop or a slab. Field-
installed electric heater accessories are available to provide
supplemental electric heat combined with electric cooling and
heating.
The units are completely assembled on rigid, removable
base rails. All piping, refrigerant charge, and electrical wiring
is factory installed and tested. The units require only electric
power and duct connections at the point of installation.
The electric heaters have nickel-chrome resistance wire ele
-
ments and utilize single point power connection.
INSPECTION
As soon as a unit is received, it should be inspected for pos
-
sible damage during transit. If damage is evident, the extent
of the damage should be noted on the carrier's freight bill. A
separate request for inspection by the carrier's agent should
be made in writing. Refer to Form 50.15-NM for additional in
-
formation.
REFERENCE
Additional information on the design, installation, operation
and service of this equipment is available in the following refer-
ence forms:
• 55.70-N1 -General Installation
• 55.70-N2 -Pre-start & Post-start Check List
• 511.26-N1.1V -Electric Heater Accessory
RENEWAL PARTS
•
Refer to Replacement PartsManual for complete listing of
replacement parts on this equipment.
All forms referenced in this instruction may be ordered from:
Standard Register
2101 West Techumseh Road
Norman, OK 73069
Toll Free: Tel. 877-318-9675/Fax. 877-379-7920
CHAMPION® SERIES
SINGLE PACKAGE HEAT PUMPS
Supersedes: 035-16004-000 (0801)
035-16004-001-A-0202
INSTALLATION INSTRUCTION

MODELS B1HA018 THRU 060
1.5 THRU 5 TON
(10 SEER)
Installer should pay particular attention to the words: NOTE, CAUTION and WARNING. Notes are intended to clarify or
make the installation easier. Cautions
are given to prevent equipment damage. Warnings are given to alert installer that per
-
sonal injury and/or equipment damage may result if installation procedure is not handled properly.
CAUTION
THE ENCLOSED INSTALLATION INSTRUCTIONS AND ANY APPLICABLE
LOCAL, STATE, AND NATIONAL CODES INCLUDING, BUT NOT LIMITED
TO, BUILDING, ELECTRICAL, AND MECHANICAL CODES.
THIS PRODUCT MUST BE INSTALLED IN STRICT COMPLIANCE WITH
WARNING
OPERATION OF THE PRODUCT COULD CAUSE PERSONAL INJURY
OR PROPERTY DAMAGE.
INCORRECT INSTALLATION MAY CREATE A CONDITION WHERE THE

Summary

General Unit Information

Limitations and Installation Guidelines

Unit Location

Installation Requirements

Electrical Data

Single Phase Electrical Data

Electrical data for 208/230V single-phase units with electric heat.

Three Phase Electrical Data

Electrical data for 208/230V three-phase units with electric heat.

Electrical Data (Continued)

460 V;575 V Three Phase Data

Electrical data for 460V and 575V three-phase units with electric heat.

Basic Unit Electrical Data

Basic Unit Specifications

Electrical data for basic units without electric heat accessories.

Supply Air CFM Measurement

Coil Delta P vs. Airflow Graph

Unit Dimensions and Clearances

Dimension Diagram

Minimum Clearance Table

Sequence of Operation

Cooling and Heating Modes

Defrost and Safety Features

Details on defrost cycle, safety switches, and lockout conditions.

Thermostat Signal Interpretation

Single Phase Unit Signals

Maintenance and Thermostat Signals

Three Phase Unit Signals

Routine Maintenance

Wiring Diagrams

208;230-1-60 Power Supply Diagram

Typical wiring diagram for 208/230V single-phase power supply configurations.

230-3-60 Power Supply Diagram

Typical wiring diagram for 230V three-phase power supply configurations.

460-3-60 & 575-3-60 Power Supply Diagram

Typical wiring diagram for 460V and 575V three-phase power supply configurations.

Wiring Diagram Explanations

Typical Wiring Diagram Legend

Explanation of symbols and abbreviations used in wiring diagrams.

Typical Wiring Diagram Notes

York B1HA036A06 Specifications

General

Brand	York
Model	B1HA036A06
Category	Heat Pump
Language	English