York B1HA060A06 User Manual

GENERAL
YORK Model B1HA units are factory assembled heat pumps
designed for outdoor installation on a rooftop or a slab. Field-
installed electric heater accessories are available to provide
supplemental electric heat combined with electric cooling and
heating.
The units are completely assembled on rigid, removable
base rails. All piping, refrigerant charge, and electrical wiring
is factory installed and tested. The units require only electric
power and duct connections at the point of installation.
The electric heaters have nickel-chrome resistance wire ele
-
ments and utilize single point power connection.
INSPECTION
As soon as a unit is received, it should be inspected for pos
-
sible damage during transit. If damage is evident, the extent
of the damage should be noted on the carrier's freight bill. A
separate request for inspection by the carrier's agent should
be made in writing. Refer to Form 50.15-NM for additional in
-
formation.
REFERENCE
Additional information on the design, installation, operation
and service of this equipment is available in the following refer-
ence forms:
• 55.70-N1 -General Installation
• 55.70-N2 -Pre-start & Post-start Check List
• 511.26-N1.1V -Electric Heater Accessory
RENEWAL PARTS
•
Refer to Replacement PartsManual for complete listing of
replacement parts on this equipment.
All forms referenced in this instruction may be ordered from:
Standard Register
2101 West Techumseh Road
Norman, OK 73069
Toll Free: Tel. 877-318-9675/Fax. 877-379-7920
CHAMPION® SERIES
SINGLE PACKAGE HEAT PUMPS
Supersedes: 035-16004-000 (0801)
035-16004-001-A-0202
INSTALLATION INSTRUCTION

MODELS B1HA018 THRU 060
1.5 THRU 5 TON
(10 SEER)
Installer should pay particular attention to the words: NOTE, CAUTION and WARNING. Notes are intended to clarify or
make the installation easier. Cautions
are given to prevent equipment damage. Warnings are given to alert installer that per
-
sonal injury and/or equipment damage may result if installation procedure is not handled properly.
CAUTION
THE ENCLOSED INSTALLATION INSTRUCTIONS AND ANY APPLICABLE
LOCAL, STATE, AND NATIONAL CODES INCLUDING, BUT NOT LIMITED
TO, BUILDING, ELECTRICAL, AND MECHANICAL CODES.
THIS PRODUCT MUST BE INSTALLED IN STRICT COMPLIANCE WITH
WARNING
OPERATION OF THE PRODUCT COULD CAUSE PERSONAL INJURY
OR PROPERTY DAMAGE.
INCORRECT INSTALLATION MAY CREATE A CONDITION WHERE THE

York B1HA060A06 Specifications

General

Type	Heat Pump
Refrigerant	R-410A
Voltage	208/230V
Phase	1
Compressor Type	Scroll
Tonnage	5 Ton
Cooling Capacity	60, 000 BTU/h

Summary

YORK CHAMPION Series Heat Pump General Information

Key Safety Instructions

Emphasizes following NOTE, CAUTION, and WARNINGs for safe installation and operation.

Installation Guidelines and Requirements

Ductwork Installation and Conversion

Unit Wiring and Service Access

Electrical Data for Heat Pump Models

Single-Phase Unit Electrical Specifications

Details electrical ratings (FLA, LRA, AMPACITY, FUSE/BREAKER) for single-phase units with electric heat.

Three-Phase Unit Electrical Specifications

Details electrical ratings (FLA, LRA, AMPACITY, FUSE/BREAKER) for three-phase units with electric heat.

Expanded Electrical Data for Heat Pumps

Additional Three-Phase Electrical Specs

Measuring Supply Air CFM

Procedure for Airflow Measurement

Step-by-step guide to measure CFM using duct plugs and manometer, referencing a graph.

Unit Dimensions and Installation Clearances

Required Minimum Installation Clearances

Unit Sequence of Operation

Cooling Mode Operation Sequence

Describes cooling operation logic, thermostat inputs, and component activation.

Heating Mode Operation Sequence

Explains heating operation logic, including heat pump and electric heat engagement.

Safety Switch and Lockout Functions

Details operation of safety switches, lockout timers, and electric heat limit controls.

Unit Maintenance Procedures

Routine Maintenance Schedule

Covers regular tasks like filter changes, coil cleaning, and motor checks.

Outdoor Coil Cleaning Guidelines

Wiring Diagram: 208/230V Single-Phase

208/230V Elementary Wiring Diagram

Explains the elementary diagram for 208/230V single-phase power supply.

Key Wiring Connections and Controls

Details connections for compressor relay, fan control, and thermostat for this power supply.

Wiring Diagram: 230V Three-Phase

230V Three-Phase Elementary Diagram

Presents the elementary wiring diagram for 230V three-phase power supply.

Three-Phase Control and Power Wiring

Details wiring for compressors, fans, and electric heat for 230V three-phase units.

Wiring Diagram: 460/575V Three-Phase

Diagram for Higher Voltage 3-Phase Power

Fan Speed Wiring Configurations

Shows wiring for different indoor fan speed settings (low, med, hi).

Wiring Diagram Symbols and Notes

Legend for Wiring Diagram Components

Important Wiring Installation Notes

Provides critical notes for field wiring, safety, and unit configuration.