York CHAMPION B1HH060 User Manual

GENERAL
YORK Model B1HH units are factory assembled heat pumps
designed for outdoor installation on a roof top or a slab. Field-
installed electric heater accessories are available to provide
supplemental electric heat combined with electric cooling and
heating.
The units are completely assembled on rigid, removable
base rails. All piping, refrigerant charge, and electrical wiring
is factory installed and tested. The units require only electric
power and duct connections at the point of installation.
The electric heaters have nickel-chrome resistance wire ele
-
ments and utilize single point power connection.
INSPECTION
As soon as a unit is received, it should be inspected for possi
-
ble damage during transit. If damage is evident, the extent of
the damage should be noted on the carrier's freight bill. A
separate request for inspection by the carrier's agent should
be made in writing. Refer to Form 50.15-NM for additional in
-
formation.
REFERENCE
Additional information on the design, installation, operation
and service ofthis equipment is available in the following refer-
ence forms:
• 55.70-N1 — General Installation
• 55.70-N2 — Pre-start & Post-start Check List
• 511.26-N1.1V — Electric Heater Accessory
REPLACEMENT PARTS
•
Refer to Replacement Parts Manual for complete listing of
replacement parts on this equipment.
Installershouldpayparticular attention to the words: NOTE, CAUTION and WARNING.Notes
areintendedtoclarify or make the
installation easier. Cautions
are given to prevent equipment damage. Warnings are given to alert installer that personal injury
and/or equipment damage may result if installation procedure is not handled properly.
CAUTION
THIS PRODUCT MUST BE INSTALLED IN STRICT COMPLIANCE WITH THE ENCLOSED INSTALLATION INSTRUCTIONS
AND ANY APPLICABLE LOCAL, STATE, AND NATIONAL CODES INCLUDING, BUT NOT LIMITED TO, BUILDING, ELEC
-
TRICAL, AND MECHANICAL CODES
WARNING
INCORRECT INSTALLATION MAY CREATE ACONDITION WHERE THE OPERATION OF THE PRODUCT COULD CAUSE
PERSONAL INJURY, PROPERTY DAMAGE AND/OR DEATH.
WARNING
DE-ENERGIZE THE ELECTRICAL POWER TO THE UNIT BEFORE ATTEMPTING TO INSPECT, REPAIR OR PERFORM
MAINTENANCE TO THE UNIT.
CHAMPION® SERIES
SINGLE PACKAGE HEAT PUMPS
Supersedes: 66297-YIM-B-1004
66297-YIM-C-0205
INSTALLATION INSTRUCTION
®
MODELS B1HH018 THRU 060
1.5 THRU 5 TON
(12 SEER)

York CHAMPION B1HH060 Specifications

General

Brand	York
Model	CHAMPION B1HH060
Category	Heat Pump
Language	English

Summary

General Unit Information

Unit Inspection Procedure

Procedure for checking the unit upon receipt for any transit damage.

Reference Information

Lists other relevant information forms for design, installation, operation, and service.

Replacement Parts Manual

Refers to the manual for listing replacement parts on this equipment.

Product Nomenclature and Identification

Installation Limitations

Outlines restrictions and requirements for installation according to codes.

Installation Guidelines

Location Selection

Guidelines for selecting a suitable installation location for the units.

Rigging and Handling

Instructions and precautions for safely moving and lifting the unit.

Clearances and Ductwork

Duct Work Installation

Instructions for adapting the unit to downflow use and connecting ductwork.

Filter Requirements

Information regarding filters, their use, and maintenance requirements.

Condensate Drain Installation

Requirement for installing a condensate trap and conforming to local codes.

Service Access Panels

Identifies removable panels for accessing serviceable components.

Thermostat Installation

Guidance on thermostat location and installation procedures.

Power and Control Wiring

Information on field wiring requirements and compliance with electrical codes.

Wiring Diagrams

Power Wiring Details

Typical field wiring diagrams for single and three-phase power supply.

Sequence of Operation

Anti-Short Cycle Timer Function

Explains the function and bypass of the anti-short cycle timer for the compressor.

Cooling Operation Sequence

Details the sequence of operations for cooling mode with a standard thermostat.

Heating Operation Sequence

Details the sequence of operations for heating mode with a standard thermostat.

Defrost Operation Details

Explains the defrost cycle initiation, termination, and safety switch operation.

Heat Pump Safety Switch Operation

Describes the function and lockout conditions of heat pump safety switches.

Electric Heat Limit Switch Operation

Explains the operation and lockout conditions of the electric heat limit switch.

Unit Maintenance

Troubleshooting Guide