York Champion Series - User Manual

DESCRIPTION
These packaged heat pumps are designed for outdoor instal-
lation. Only utility and duct connections are required at the
point of installation.
Field-installed electric heater accessories are available to
provide electric heat, if required.
STANDARD FEATURES / BENEFITS
OPERATING EFFICIENCY - All units provide high operating
efficiencies of 10 SEER or greater, 3.0 COP or greater and up to
7.0 HSPF. All efficiencies exceed legislated minimum levels.
ON SITE FLEXIBILITY - All model sizes share a common,
compact design cabinet with a single footprint. The installer
has the flexibility of setting one curb or pad and placing the
proper tonnage unit on that curb after the internal load has
been determined. Field convertible duct connections from
side shot to down shot allows the installer to have greater
flexibility and needs to carry less inventory.
LOWER INSTALLATION COST - Installation time and costs
are reduced by easy power and control wiring connections.
The small base dimension means less space is required on
the ground or roof, plus, the installer can fit this unit between
the wheel wells of full size pick-up truck. All models are well
under 500 pounds.
All units are completely wired, charged with R-22 and tested
prior to shipment. Unique test stations using a new state of the
art computerized process system are used to insure product
quality. Refrigerant charge, and component part numbers are
verified via computers at manufacturing point. Vital run test sta
-
tistics such as system pressure, motor currents, air velocity and
temperature and unit vibration are monitored and recorded by
the system to insure unit performance.
Equal size, side supply and return duct connections allows
easy hook-upofducts tomatchlowcrawl spaces without tran
-
sition pieces.
UTILITY CONNECTIONS MADE EASY - Electrical utility
knockoutsare provided through the bottom as well as the side
of the unit. Utility connections can be made quickly and with a
minimum amount of field labor. A field supplied and field in
-
stalled electrical disconnect switch must be installed.
CONVERTIBLE AIRFLOW DESIGN - The bottom duct open
-
ings are covered when they leave the factory ready to be used
for a side supply / side return application. If a bottom supply / bot
-
tom return application is desired, you simply remove the two
panels from the bottom of the unit and place them in the side
supply / side return duct openings. No panel cutting is required
and no accessory panel is necessary. Convertible airflow design
allows maximum field flexibility and minimum inventory.
CONDENSATE PAN - A non-corrosive, long-lasting, water-tight
panispositioned belowthe evaporator coil to collect and drainall
condensate. Less collection of stagnate condensate will build-
up. The condensate pan conforms to ASHRAE 62-89 standards
(Ventilation for Acceptable Indoor Air Quality).
CONDENSATE DRAIN - The heavy duty,
3
4
inch NPTI copper
connection is more tolerable during installation and is more
durable over time. The connection is rigidly mounted to as
-
sure proper fit and leak tight seal.
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
036-21311-003-A-0104
®
TECHNICAL GUIDE
Champion Series
SINGLE PACKAGE
HEAT PUMPS
BHA018 THRU 060
1-1/2 THRU 5 NOMINAL TONS
10 SEER
®

Summary

Description

Operating Efficiency

Details SEER, COP, and HSPF ratings, meeting minimum legislated levels.

On Site Flexibility

Common cabinet design, single footprint, convertible duct connections for installer flexibility.

Utility Connections Made Easy

Knockouts for quick electrical connections; requires field-installed disconnect switch.

Convertible Airflow Design

Bottom openings convertible to side supply/return without panel cutting.

Standard Features and Benefits

Durable Finish

Heavy-duty powder-painted galvanized steel cabinet, resists corrosion, ASTM-B117 rated.

Low Operating Sound Level

Upward airflow, isolated compressor, rippled fins, and formed base pan reduce noise.

Protected Compressor

Internally protected against high pressure/temperature via relief valve and sensor.

Easy Service Access

Large hinged panel for electrical controls; slide-out blower compartment.

Field-Installed Accessories

Economizer Down Discharge; Supply Kit

Modulating economizer for simultaneous operation, includes filter, dry bulb sensor.

Motorized Fresh Air Damper

Duct-mounted damper for side/unit supply/return, 0-50% outdoor air, closes on power loss.

Electric Heaters

Easy installation electric heat strips; available from 5.0 KW, designed for single/dual point connections.

Ratings

Physical Data

Cooling Capacities - 1-1;2 Ton (BHA018)

Heating Capacities - 1-1;2 Ton (BHA018)

Additional Static Pressure Resistance

Side and Bottom Supply Air Blower Performance

Field Wiring Diagram

Electrical Data (Basic Unit)

Unit Dimensions

Clearances

Typical Applications

Mechanical Specifications

General Description

Factory-assembled, single packaged heat pumps for outdoor installation, minimum SEER 10.0.

Unit Cabinet

G90 galvanized steel, powder-painted finish, water-shed top, coil guard, insulated blower section.

Indoor (Supply) Fan Assembly

Direct-drive, multi-speed fan, double-inlet wheel, sealed bearings, slide-out design.

Refrigerant Components

Hermetic compressors, aluminum plate fin coils, fixed-orifice expansion devices, filter/strainer.

Unit Controls

Electric Heating Section

Nickel chromium elements, 5-25 KW range, primary limit control, slide-out assembly.

Unit Operating Characteristics

Operates at 125°F outdoor temp; compressor operates down to 45°F outdoor temp.

York Champion Series Specifications

General

Series	Champion Series
Refrigerant	R-410A
Warranty	10-Year Limited Parts Warranty
Type	Heat Pump
SEER Rating	Up to 19
HSPF Rating	Up to 10
Compressor Type	Scroll