York F3EH090 User Manual

GENERAL
These completely assembled indoor units include a well-
insulated cabinet, a copper tube/aluminum fin coil, throw
-
away filters, a centrifugal blower, a blower motor, an adjust
-
able V-belt drive, a blower motor contactor and a small
holding charge of an inert gas. They also include a filter-
drier, an expansion valve and a distributor that are only used
during the cooling cycle plus a check valve to provide the
proper flow of refrigerant through the coil during both the
cooling and heating cycles.
Supplemental resistance heaters, a supply air plenum, a return
air grille and a base are available as accessories for field instal
-
lation.
The units are shipped in the vertical position ready for field in
-
stallation. For horizontal installation, reverse the solid bottom
panel and the return air duct flange on the front of the unit.
REFERENCE
This instruction covers the installation of the indoor unit. For in
-
formation on the installation and operation of the matching out
-
door unit, refer to Form 035-15410-002.
Renewal Parts:
•
Refer to Parts Manual for complete listing of replacement
parts on this equipment.
All forms referenced in this instruction may be ordered from:
Standard Register
Toll Free Tel.: 877-318-9675
Toll Free Fax: 877-379-7920
Installer should pay particular attention to the words: NOTE,
CAUTION and WARNING. Notes
are intended to clarify or
make the installation easier. Cautions
are given to prevent
equipment damage. Warnings
are given to alert the installer
that personal injury and/or equipment damage may result if the
installation procedure is not handled properly.
INSPECTION
As soon as a unit is received, it should be inspected for possi
-
ble damage during transit. If damage is evident, the extent of
the damage should be noted on the carrier's freight bill. Asepa
-
MODELS F3EH090 & F4EH120
(50 and 60 Hz)
INSTALLATION
MANUAL
Supersedes: 515.41-N2Y (692)/035-09651-000 035-09651-001-A-0304
SPLIT-SYSTEM HEAT PUMPS
INDOOR UNITS
CAUTION
THIS PRODUCT MUST BE INSTALLED IN STRICT COMPLIANCE
WITH THE ENCLOSED INSTALLATION INSTRUCTIONS AND
ANY APPLICABLE LOCAL, STATE, AND NATIONAL CODES
INCLUDING, BUT NOT LIMITED TO, BUILDING, ELECTRICAL,
AND MECHANICAL CODES.
WARNING
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN CAUSE INJURY OR
PROPERTY DAMAGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFORMATION, CONSULT A
QUALIFIED INSTALLER, SERVICE AGENCY OR THE GAS
SUPPLIER.

York F3EH090 Specifications

General

Brand	York
Model	F3EH090
Category	Heat Pump
Language	English

Summary

General Information

Reference

Information on the installation and operation of the matching outdoor unit.

Renewal Parts

Refer to Parts Manual for complete listing of replacement parts.

Inspection

Installation

Limitations

Units must be installed in accordance with national and local safety codes.

Location

Indoor units must be located within the building structure, inside or outside conditioned space.

Rigging and Handling

Exercise care when moving the unit. Do not remove packaging until near installation.

Clearances

All units require certain minimum clearances for proper operation and service.

Vertical / Horizontal Installation

Units are shipped for vertical installation but can be converted for horizontal.

Duct Connections

Design and install all ducts in accordance with national and/or local codes.

Refrigerant Mains

Provide an internally clean and dry system and use procedures and materials that conform with standards.

Installing Refrigerant Mains

Provisions for recovering refrigerant releases must be available during all phases of installation.

Drain Connection

The drain line MUST be trapped because the coil is located on the negative side of the supply air blower.

Supply Air Blower Adjustment

Adjust the supply air blower RPM based on required CFM and static resistances.

Power and Control Wiring

Install electrical wiring in accordance with the latest National Electrical Code (NFPA Standard No. 70).

Maintenance

Indoor Coil

Do not allow dirt to accumulate. Clean as often as necessary to assure good system performance.

Drain Pan

The condensate drain pan should be inspected regularly to assure proper drainage.

Filters

Filters must be replaced as often as necessary to assure good air flow and filtering action.

Lubrication

The bearings for the blower shaft and motor are permanently lubricated.

Belts

Maintain belt tension to extend belt life. Replace when signs of failure begin to appear.