York H1RA042S06 User Manual

TECHNICAL GUIDE
SPLIT-SYSTEM AIR CONDITIONERS
10 SEER
MODELS:
H*RA018 THRU 060
(1.5 THRU 5 NOMINAL TONS, 1 PH)
H*RA036 THRU 090
(3 THRU 7.5 NOMINAL TONS, 3 PH)
MODELS: 018 - 060 (1 PH & 3 PH)
MODELS: 076 - 090 (3 PH)
Due to continuous product improvement, specifica-
tions are subject to change without notice.
Visit us on the web at www.york.com for the most
up-to-date technical information.
Additional rating information can be found at
www.ariprimenet.org.
LISTED
This product was manufactured
in a plant whose quality system
is certified/registered as being
in conformity with ISO 9001.
Certification applies only
when the complete
system is listed
with ARI.
R
N
E
M
P
I
U
Q
E
T
Y
R
A
T
I
N
U
0
1
2
A
R
I
R
A
D
N
A
T
S
D
I
S
N
O
T
C
E
S
F
O
C
C
I
F
I
T
R
E
N
O
I
T
A
H
T
I
W
C
G
N
I
Y
L
P
M
O
S
A
I
R
A
O
T
D
E
I
F
I
T
R
E
C
R
E
R
U
T
C
A
F
U
N
A
M
C
-
G
N
I
N
O
I
T
I
D
N
O
R
I
A
®
036-21121-002 Rev. B (0103)
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
DESCRIPTION
The 10 SEER Series condensing unit is the outdoor part of a
versatile system of air conditioning. It is designed to be cus-
tom-matched with one of UPG’s complete line of evaporator
sections, each designed to serve a specific function. Match-
ing Air Handlers are available for upflow, downflow or hori-
zontal applications to provide a complete system. Electric
Heaters are available if required. Add-On coils are available
for use with upflow, downflow or horizontal furnaces and air
handlers.
WARRANTY
Single Phase Units:
5-year limited parts warranty.
5-year limited compressor warranty.
Three Phase Units:
1-year limited parts warranty.
5-year limited compressor warranty.
FEATURES
• QUALITY CONDENSER COILS - The coil is constructed
of enhanced copper tube and aluminum fins.
• COIL PROTECTION - Coils are protected from damage by
a polymer mesh applied between the coil face, and a PVC
coated steel coil guard.
• PROTECTED COMPRESSOR - The compressor is inter-
nally protected against high pressure and temperature.
This is accomplished by the simultaneous operation of
high pressure relief valve and a temperature sensor which
protects the compressor if undesirable operating condi-
tions occur. A liquid line filter-drier further protects the
compressor.
• DURABLE FINISH - The cabinet is made of pre-painted
steel. The pre-treated flat galvanized steel provides a bet-
ter paint to steel bond, which resists corrosion and rust
creep. Special primer formulas and matted desert sand fin-
ish insure less fading when exposed to sunlight.
• LOWER INSTALLED COST - Installation time and costs
are reduced by easy power and control wiring connec-
tions. Discharge line heat exchanger knockouts are pro-
vided, if required. Available in sweat connect models only.
The unit contains enough refrigerant for matching indoor
coils and 15 feet of interconnecting piping. The small base
dimension means less space is required on the ground or
roof.
• TOP DISCHARGE - The warm air from the top mounted
fan is blown up away from the structure and any landscap-
ing. This allows compact location on multi-unit applica-
tions.
• LOW OPERATING SOUND LEVEL - The upward air flow
carries the normal operating noise up away from the living
area. The rigid top panel effectively isolates any motor
sound. Isolator mounted compressor and the rippled fins
of the condenser coil muffle the normal fan motor and
compressor operating sounds.
• LOW MAINTENANCE - Long life permanently lubricated
motor-bearings need no annual servicing.
• EASY SERVICE ACCESS - Fully exposed refrigerant con-
nections, a single panel covering the electrical controls
and the molex plug in the control box connecting the con-
denser fan, make for easy servicing of the unit.
• SECURED SERVICE VALVES - Secured re-usable ser-
vice valves are provided on both the liquid and vapor
sweat connections for ease of evacuating and charging.
• U.L. and C.U.L. listed - approved for outdoor application.
Certified in accordance with the Unitary Small Equipment cer-
tification program, which is based on ARI Standard 210/240.

York H1RA042S06 Specifications

General

Tonnage	3.5 Ton
Energy Efficiency Ratio (EER)	11.5
Power Supply	208/230V, 1 Phase, 60 Hz
Refrigerant	R-410A
Noise Level (Indoor Unit)	48 dB(A)
Cooling Capacity	42000 BTU/hr

Summary

Product Introduction

System Description

Overview of the 10 SEER condensing unit and its system matching capabilities.

Warranty Information

Details limited warranty periods for single and three phase units.

Key Product Features

Highlights key attributes of the condensing unit, such as coil quality and durability.

Technical Specifications

1-Phase Physical and Electrical Data

Provides detailed physical and electrical specifications for single-phase models.

3-Phase Physical and Electrical Data

Provides detailed physical and electrical specifications for three-phase models.

System Configuration and Charge

1-Phase R-22 Charge and Orifice Data

Details R-22 charge and orifice size for 1-phase matched systems.

System Charge Procedures

Outlines steps for verifying and marking system charge and orifice size.

3-Phase System Configuration and Charge

3-Phase R-22 Charge and Orifice Data

Details R-22 charge and orifice size for 3-phase matched systems.

Cooling Performance Data - General

1-Phase General Cooling Performance

Presents general cooling performance data for 1-phase units.

3-Phase General Cooling Performance

Presents general cooling performance data for 3-phase units.

Cooling Capacity with Furnaces

1-Phase Furnace Cooling Capacity

Shows cooling capacity for 1-phase units matched with furnaces.

3-Phase Furnace Cooling Capacity

Shows cooling capacity for 3-phase units matched with furnaces.

Cooling Capacity with Furnaces (Continued)

1-Phase Furnace Capacity (Cont.)

Continues cooling capacity data for 1-phase units with furnaces.

3-Phase Furnace Capacity (Cont.)

Continues cooling capacity data for 3-phase units with furnaces.

Detailed Cooling Performance Data

1-Phase Model Performance

Detailed cooling performance for specific 1-phase models at varying conditions.

3-Phase Model Performance

Detailed cooling performance for specific 3-phase models at varying conditions.

Accessories, Sound, and Installation

Optional Accessories

Lists optional accessories like hard start kits and compressor blankets.

Sound Ratings

Provides sound ratings in decibels for various unit models.

Typical Installation Guidelines

Illustrates typical installation clearances and wiring connections.

Field Wiring Diagrams

1-Phase Field Wiring

Shows typical field wiring connections for single-phase outdoor units.

3-Phase Field Wiring

Shows typical field wiring connections for three-phase outdoor units.

Performance Multipliers - Coil Matching

H1RA018S06 Coil Multipliers

Multipliers for determining performance with indoor coils for H1RA018S06.

Performance Multipliers - Coil Matching

H1RA024S06 Coil Multipliers

Multipliers for determining performance with indoor coils for H1RA024S06.

Performance Multipliers - Coil Matching

H2RA030S06 Coil Multipliers

Multipliers for determining performance with indoor coils for H2RA030S06.

Performance Multipliers - Coil Matching

H2RA036S06/H1RA036S(25,46) Coil Multipliers

Multipliers for performance with indoor coils for H2RA036S06/H1RA036S(25,46).

Performance Multipliers - Coil Matching

H1RA042S06/H1RA042S(25,46) Coil Multipliers

Multipliers for performance with indoor coils for H1RA042S06/H1RA042S(25,46).

Performance Multipliers - Coil Matching

H1RA048S06/H1RA048S(25,46) Coil Multipliers

Multipliers for performance with indoor coils for H1RA048S06/H1RA048S(25,46).

Performance Multipliers - Coil Matching

H3RA060S06 Coil Multipliers

Multipliers for determining performance with indoor coils for H3RA060S06.

Performance Multipliers - Coil Matching

H1RA060S(25,46) Coil Multipliers

Multipliers for determining performance with indoor coils for H1RA060S(25,46).

Performance Multipliers - Coil Matching

H1RA076S(25,46) Coil Multipliers

Multipliers for determining performance with indoor coils for H1RA076S(25,46).

Performance Multipliers - Coil Matching

H1RA090S(25,46) Coil Multipliers

Multipliers for determining performance with indoor coils for H1RA090S(25,46).

Matching Indoor Components

Add-On Coils for Furnace Applications

Illustrates add-on coils available for furnace applications.

Air Handlers for Non-Furnace Applications

Shows air handler units for non-furnace applications.