Zebra 105SL - Page 11

32056L Rev. 2 12/4/01 105SL Maintenance Manual Page ix
TABLE OF CONTENTS
Figure 5-6. Main and Lower Platen Rollers ....................................................................... 5-15
Figure 5-7. Media Supply Hanger ...................................................................................... 5-17
Figure 5-8. Ribbon Supply Spindle .................................................................................... 5-19
Figure 5-9. Ribbon Take-up Spindle and Pulley ................................................................ 5-21
Figure 5-10. Media Guide Assembly .................................................................................. 5-22
Figure 5-11. Front Panel and LCD Display ........................................................................ 5-23
Figure 5-12. Power Supplies .............................................................................................. 5-24
Figure 5-13. Pivot Bar Assembly ....................................................................................... 5-25
Figure 5-14. Backing Rewind Assembly ............................................................................ 5-27
Figure 5-15. Media Rewind Option .................................................................................... 5-29
Figure 5-16. Cutter Option (View 1) ................................................................................... 5-31
Figure 5-17. Cutter Option (View 2) ................................................................................... 5-32
Figure 5-18. Communication Options ................................................................................ 5-33
Figure 5-19. Fanfold Bin Option ......................................................................................... 5-34
Figure 6-1. Backing Rewind Option Kit ................................................................................ 6-2
Figure 6-2. Liner Rewind Assembly Installation ................................................................... 6-3
Figure 6-3. Take-Label Sensors .......................................................................................... 6-5
Figure 6-4. Sensor Connector Location (Printer Configurations 10500-0XXX-XXXX
and 10500-1XXX-XXXX) ................................................................................................ 6-6
Figure 6-5. Sensor Connector Location (Printer Configurations 10500-2XXX-XXXX
and 10500-3XXX-XXXX) ................................................................................................ 6-6
Figure 6-6. Initial Rewind Drive Belt Tensioning .................................................................. 6-7
Figure 6-7. Platen Support Bracket Adjustment .................................................................. 6-8
Figure 6-8. Media Rewind Option Kit ................................................................................. 6-10
Figure 6-9. Media Rewind Installation ................................................................................ 6-11
Figure 6-10. Rewind Plate Installation ............................................................................... 6-13
Figure 6-11. Cutter Catch Tray Installation ........................................................................ 6-16
Figure 6-12. Cutter Catch Tray Length and Width Adjustments ........................................ 6-17
Figure 6-13. Internal Fanfold Supply Bin Installation ......................................................... 6-18
Figure 6-14. Rear Panel ..................................................................................................... 6-19
Figure 6-15. Internal PrintServer ll Installation (Printer Configurations 10500-0XXX-XXXX and
10500-1XXX-XXXX) ..................................................................................................... 6-20
Figure 6-16. Internal PrintServer ll Installation (Printer Configurations 10500-2XXX-XXXX and
10500-3XXX-XXXX) ..................................................................................................... 6-21
Figure 6-17. External PrintServer ...................................................................................... 6-22
Figure 6-18. Coax Communications Interface Board Installation (Printer Configurations
10500-0XXX-XXXX and 10500-1XXX-XXXX) .............................................................. 6-23
Figure 6-19. Coax Communications Interface Board Installation (Printer Configurations
10500-2XXX-XXXX and 10500-3XXX-XXXX) .............................................................. 6-23
Figure 6-20. Coax Adapter Cable and Interface Hook up ................................................. 6-24
Figure 6-21. Twinax Interface Board Installation (Printer Configurations 10500-0XXX-XXXX
and 10500-1XXX-XXXX) .............................................................................................. 6-26
Figure 6-22. Twinax Interface Board Installation (Printer Configurations 10500-2XXX-XXXX
and 10500-3XXX-XXXX) .............................................................................................. 6-27
Figure 6-23. Twinax Connections ...................................................................................... 6-28