Zebra 105SL User Manual

Page viii 105SL Maintenance Manual 32056L Rev. 2 12/4/01
TABLE OF CONTENTS
Figure 4-35. Membrane Switch and Front Panel ...............................................................4-49
Figure 4-36. Remove/Install Membrane Switch and Front Panel Assembly ......................4-50
Figure 4-37. LCD PCB Removal/Installation ......................................................................4-51
Figure 4-38. Media Supply Hanger Tabs ...........................................................................4-52
Figure 4-40. International Safety Organizations .................................................................4-53
Figure 4-39. Media Supply Hanger Installation ..................................................................4-53
Figure 4-41. AC Power Fuse Replacement 10500-0XXX-XXXX and 10500-1XXX-XXXX 4-54
Figure 4-42. AC Power Fuse Replacement 10500-2XXX-XXXX and 10500-3XXX-XXXX 4-55
Figure 4-43. Cutter Main Link and Slotted Removal and Installation .................................4-57
Figure 4-44. Cutter PCB Removal and Installation ............................................................4-59
Figure 4-45. Cutter PCB Connections ................................................................................4-60
Figure 4-46. Mechanical Assembly Positioning ..................................................................4-63
Figure 4-47. Cutter Motor Replacement .............................................................................4-65
Figure 4-48. Platen Pulley Replacement ............................................................................4-66
Figure 4-49. Upper Media Sensor Replacement ................................................................4-67
Figure 4-51. Upper Media Sensor and Bracket ..................................................................4-68
Figure 4-50. Linen Thread Placement ................................................................................4-68
Figure 4-52. Lower Media Sensor and Bracket ..................................................................4-69
Figure 4-53. Media Rewind Spindle Replacement .............................................................4-71
Figure 4-54. Ribbon Supply Spindle Kit Parts and Mounting Location ..............................4-72
Figure 4-55. Ribbon Take-up Spindle ................................................................................4-74
Figure 4-56. Rear Panel Fasteners ....................................................................................4-75
Figure 4-57. Rear Panel Wiring ..........................................................................................4-76
Figure 4-58. Ribbon Take-up Pulley Replacement ............................................................4-77
Figure 4-59. Media Take-up Pulley Replacement ..............................................................4-79
Figure 4-60. Peel Roller Pulley Replacement ....................................................................4-80
Figure 4-61. Pivot Bar, Handle and Toggle Parts ...............................................................4-81
Figure 4-62. Rewind Plate Replacement ............................................................................4-83
Figure 4-63. Printhead Replacement .................................................................................4-84
Figure 4-64. Guard Plate and Sensor ................................................................................4-85
Figure 4-65. Wire Tie Removal and Installation .................................................................4-85
Figure 4-66. Printhead Cleaning .........................................................................................4-86
Figure 4-67. Take-Label Sensors .......................................................................................4-87
Figure 4-68. Freeing Side Plate for Removal .....................................................................4-89
Figure 4-69. Side Plate Removal and Installation ..............................................................4-90
Figure 4-70. DC Stepper Motor Removal and Installation .................................................4-91
Figure 4-71. Black Mark Sensor Installation .......................................................................4-92
Figure 4-72. Media Cover Replacement ............................................................................4-93
Figure 5-1. Final Assembly (View 1) .....................................................................................5-5
Figure 5-2. Final Assembly (View 2) .....................................................................................5-7
Figure 5-3. Final Assembly (View 3 ) for Configuration Numbers 10500-0XXX-XXXX
and 10500-1XXX-XXXX ..................................................................................................5-9
Figure 5-4. Final Assembly (View 4) for Configuration Numbers 10500-2XXX-XXXX
and 10500-3XXX-XXXX ................................................................................................5-11
Figure 5-5. Printhead Support Assembly ...........................................................................5-13

Zebra 105SL Specifications

General

Print technology	Direct thermal
Display	LCD
Product color	Gray
Network ready	Yes
Dimensions (WxDxH)	283 x 495 x 394 mm
Standard interfaces	Parallel, Serial
Internal memory	6 MB
Maximum label width	115 mm
Maximum label length	0.991 m
Power requirements	90-264 VAC, 48-63 Hz

Weight and Dimensions

Depth	495 mm
Width	283 mm
Height	394 mm
Weight	29000 g