Zebra 105SL - Page 9

32056L Rev. 2 12/4/01 105SL Maintenance Manual Page vii
TABLE OF CONTENTS
Figure 3-7. Format 1 and 4 Test Sample Label ................................................................... 3-9
Figure 3-8. Format 2 and 5 Test Sample Label ................................................................... 3-9
Figure 3-9. Format 3 and 6 Test Sample Label ................................................................. 3-10
Figure 3-10. Format 7 and 11 Test Sample Label ............................................................. 3-10
Figure 3-11. Format 8 and 12 Test Sample Label ............................................................. 3-10
Figure 3-12. Format 9 and 13 Test Sample Label ............................................................. 3-11
Figure 3-13. Format 10 and 14 Test Sample Label ........................................................... 3-11
Figure 4-1. Cleaning a Typical Printhead ............................................................................. 4-6
Figure 4-2. Removal and Installation of Snap Plate ............................................................ 4-7
Figure 4-3. External Printer Components ............................................................................ 4-8
Figure 4-4. Interconnection Diagram for Printer Configurations 10500-0XXX-XXXX
and 10500-1XXX-XXXX ................................................................................................. 4-9
Figure 4-5. Interconnection Diagram for Printer Configurations 10500-2XXX-XXXX and
10500-3XXX-XXXX ...................................................................................................... 4-10
Figure 4-6. Power Switch and Power Cord Removal and Installation ............................... 4-11
Figure 4-7. Removing and Installing Data Cables ............................................................. 4-11
Figure 4-8. Removing and Installing the Electronics Cover ............................................... 4-12
Figure 4-9. DC Power Supply Removal and Installation .................................................... 4-14
Figure 4-10. AC Power Supply and Main Logic Board Removal/Installation .................... 4-15
Figure 4-11. AC/DC Power Supply Removal and Installation ........................................... 4-17
Figure 4-12. Main Logic Board Removal and Installation (Printer Configurations
10500-0XXX-XXXX and 10500-1XXX-XXXX) .............................................................. 4-19
Figure 4-13. Main Logic Board Removal and Installation (Printer Configurations
10500-2XXX-XXXX and 10500-3XXX-XXXX) .............................................................. 4-21
Figure 4-14. Main Drive Belt Adjustment ........................................................................... 4-23
Figure 4-15. Main Drive Belt .............................................................................................. 4-24
Figure 4-16. Rewind Drive Belt Tension Adjustment ......................................................... 4-25
Figure 4-17. Rewind Drive Belt Removal and Installation ................................................. 4-27
Figure 4-19. Printhead Resistance Value Label ................................................................ 4-28
Figure 4-18. Printhead Replacement ................................................................................. 4-28
Figure 4-20. Printhead Cleaning ........................................................................................ 4-29
Figure 4-21. Initial Toggle Setting ...................................................................................... 4-30
Figure 4-22. Printhead Adjustment .................................................................................... 4-32
Figure 4-23. Wear Plate Adjustment .................................................................................. 4-33
Figure 4-24. Upper Transmissive Media Sensor Position Adjustment .............................. 4-36
Figure 4-25. Lower Transmissive Media Sensor Position Adjustment .............................. 4-36
Figure 4-26. Take Label Sensor Location .......................................................................... 4-37
Figure 4-28. Peel-Off Lower Roller Alignment ................................................................... 4-38
Figure 4-27. Rewind Plate Assembly ................................................................................. 4-38
Figure 4-29. Spindle Tension Adjustments ........................................................................ 4-40
Figure 4-30. Media Rewind Spindle ................................................................................... 4-41
Figure 4-31. Ribbon Supply Spindle Maintenance ............................................................ 4-42
Figure 4-32. Ribbon Take-Up Spindle Maintenance .......................................................... 4-43
Figure 4-33. Platen Roller Removal ................................................................................... 4-45
Figure 4-34. Peel Roller Kit Parts ...................................................................................... 4-47