Zebra DS3608 User Manual (English)

To Next Page

1 2

3 4

STEP 1 - CONNECT HOST INTERFACE

SCANNER FEATURES

See Product Reference Guide

for detailed information

NOTE: Cables may vary depending on configuration

STEP 2 - SET UP INTERFACE (Scan Host Bar Codes)

1 Scan Window

2 Scan Trigger

3 LED

4 Beeper

USB

Keyboard Wedge

USB

Scan ONE of the bar codes below

Keyboard Wedge

Scan a bar code below

*USB KEYBOARD (HID)

SNAPI WITHOUT IMAGING

IBM PC/AT and IBM PC COMPATIBLE

IBM HAND-HELD USB

SIMPLE COM PORT EMULATION

IBM TABLE TOP USB

USB CDC Host

1. Insert cable fully so that the connector is flush with the scanner surface.

2. Loosen metal lock plate screws using a PH1 driver.

3. Slide lock plate to fully locked position.

4. Tighten screw using a PH1 driver (torque: 5 in-lb).

IBM 46XX

Scan ONE of the bar codes below

The Auto-Host Detect Cable feature automatically detects the host interface type,

but there is no default setting. Scan one of the bar codes below to select the

appropriate port.

NON-IBM SCANNER EMULATION (PORT 5B)

HAND-HELD SCANNER EMULATION (PORT 9B)

TABLE-TOP SCANNER EMULATION (PORT 17)

ACCESSORIES

The interface cable automatically detects the host interface type and uses the

default setting. If the default (*) does not meet your requirements, scan another

host bar code below.

The interface cable automatically detects the host interface type and uses the

default setting. If the default (*) does not meet your requirements, scan another

host bar code below.

The Auto-Host Detect Cable feature automatically detects the host interface type

and uses the default setting. If the default (*) does not meet your requirements,

scan the IBM PC/AT and IBM PC COMPATIBLE bar code below.

USB - OVERRIDE CAPS LOCK KEY (ENABLE)

*USB - DO NOT OVERRIDE CAPS LOCK KEY (DISABLE)

*IBM AT NOTEBOOK

SNAPI WITH IMAGING

SSI OVER USB CDC

USB OPOS HAND- HELD

RS-232

Scan ONE of the bar codes below

ICL RS-232

NIXDORF RS-232 MODE A

NIXDORF RS-232 MODE B

FUJITSU RS-232

OPOS/JPOS

*STANDARD RS-232

http://www.zebra.com/3600series

USB CAPS LOCK OVERRIDE BAR CODE

ADD A TAB KEY

To add a Tab key after scanned data, scan

the bar code below.

ADD A TAB KEY

TAB KEY BAR CODE

RETURN TO FACTORY DEFAULTS

SET DEFAULTS / ENTER KEY BAR CODESCABLE ATTACHMENT

ADD AN ENTER KEY

To add an Enter key after scanned data, scan

the bar code below.

(Carriage Return/Line Feed)

ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)

DS3608

Quick Start Guide

Digital Scanner

POST IN WORK AREAPOST IN WORK AREA

Intellistand

Forklift Holder

Other manuals for Zebra DS3608

Product Reference Guide456 pages

User Guide2 pages

Need help?

Do you have a question about the Zebra DS3608 and is the answer not in the manual?

Zebra DS3608 Specifications

General

Type	Handheld bar code reader
Wavelength	655 nm
Sensor type	Laser
Scanner type	1D/2D
Tilt reading angle	0 - 360 °
Pitch reading angle	0 - 65 °
Light levels (direct sunlight)	0 - 108000 lx
Linear (1D) barcodes supported	Codabar, Code 11, Code 128, Code 39, Code 93, EAN 128, EAN 2, EAN 5, EAN-13, EAN-8, GS1 DataBar, Industrial 2 of 5, MSI, U.P.C., UPC-A, UPC-E
Optical sensor resolution (W x H)	1280 x 960 pixels
2D (matrix & stacked) barcodes supported	Aztec Code, Composite Codes, Data Matrix, Han Xin, MaxiCode, Micro QR Code, MicroPDF417, PDF417, QR Code, TLC-39
Input voltage	4.5 - 5.5 V
Power source type	RS-232, USB
Certification	RoHS EN 50581: 2012
Product color	Black, Grey
LED indicators	Yes
International Protection (IP) code	IP65
Standard interfaces	Keyboard wedge, RS-232, USB
Connectivity technology	Wired
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	-30 - 50 °C
Operating relative humidity (H-H)	5 - 95 %
Harmonized System (HS) code	84716070