Zebra DS3678

To Next Page

STEP 1 - CONNECT HOST INTERFACE

SCANNER FEATURES

See Product Reference Guide

for detailed information

NOTE: Cables may vary depending on configuration

STEP 2 - SET UP INTERFACE (Scan Host Bar Codes)

1 Scan Window

3 Radio LED

4 LEDs

USB

Keyboard Wedge

USB

Scan ONE of the bar codes below

Keyboard Wedge

Scan a bar code below

*USB KEYBOARD (HID)

SNAPI WITHOUT IMAGING

IBM PC/AT and IBM PC COMPATIBLE

IBM HAND-HELD USB

SIMPLE COM PORT EMULATION

IBM TABLE TOP USB

USB CDC Host

IBM 46XX

Scan ONE of the bar codes below

The Auto-Host Detect Cable feature automatically detects the host interface type,

but there is no default setting. Scan one of the bar codes below to select the

appropriate port.

NON-IBM SCANNER EMULATION (PORT 5B)

HAND-HELD SCANNER EMULATION (PORT 9B)

TABLE-TOP SCANNER EMULATION (PORT 17)

CRADLE INSERTION

The interface cable automatically detects the host interface type and uses the

default setting. If the default (*) does not meet your requirements, scan another

host bar code below.

The interface cable automatically detects the host interface type and uses the

default setting. If the default (*) does not meet your requirements, scan another

host bar code below.

The Auto-Host Detect Cable feature automatically detects the host interface type

and uses the default setting. If the default (*) does not meet your requirements,

scan the IBM PC/AT and IBM PC COMPATIBLE bar code below.

USB - OVERRIDE CAPS LOCK KEY (ENABLE)

*USB - DO NOT OVERRIDE CAPS LOCK KEY (DISABLE)

*IBM AT NOTEBOOK

SNAPI WITH IMAGING

SSI OVER USB CDC

USB OPOS HAND- HELD

RS-232

Scan ONE of the bar codes below

ICL RS-232

NIXDORF RS-232 MODE A

NIXDORF RS-232 MODE B

FUJITSU RS-232

OPOS/JPOS

*STANDARD RS-232

http://www.zebra.com/3600series

USB CAPS LOCK OVERRIDE BAR CODE

ADD A TAB KEY

To add a Tab key after scanned data, scan

the bar code below.

ADD A TAB KEY

TAB KEY BAR CODE

RETURN TO FACTORY DEFAULTS

SET DEFAULTS / ENTER KEY BAR CODESCRADLE CABLE CONNECTION

ADD AN ENTER KEY

To add an Enter key after scanned data, scan

the bar code below.

(Carriage Return/Line Feed)

ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)

DS3678

Quick Start Guide

Digital Scanner

POST IN WORK AREAPOST IN WORK AREA

BATTERY INSERTION/REMOVAL

Lock

Unlock

Latch

Host Port

(Under Latch)

123Scan

is an easy-to-use, PC-based software tool that enables rapid and easy customized setup of a scanner via a bar code or USB cable. For more information, visit: http://www.zebra.com/123Scan

123

can

5 Beeper

6 Scan Trigger

Battery LED

Page Button

LEDs (two)

Need help?

Do you have a question about the Zebra DS3678 and is the answer not in the manual?

Zebra DS3678 Specifications

General

Type	Handheld bar code reader
Wavelength	655 nm
Sensor type	Laser
Scanner type	1D/2D
Yaw reading angle	-45 - 45 °
Tilt reading angle	-65 - 65 °
Optical sensor resolution	1280 pixels
Linear (1D) barcodes supported	Codabar, Code 11, Code 128, Code 39, Code 93, GS1-128 (UCC/EAN-128), MSI, Plessey, U.P.C.
2D (matrix & stacked) barcodes supported	Aztec Code, Composite Codes, Data Matrix, Han Xin, MaxiCode, Micro QR Code, MicroPDF417, PDF417, QR Code, TLC-39
Battery capacity	3100 mAh
Power source type	Battery
Number of reads per charge	100000
Product color	Black, Green
Housing material	-
Protection features	Dust resistant, Shock resistant, Water resistant
Programming function	Yes
International Protection (IP) code	IP67
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	-20 - 50 °C
Operating relative humidity (H-H)	5 - 95 %
Wireless range	100 m
Bluetooth version	4.0
Standard interfaces	RS-232, USB, Keyboard wedge
Connectivity technology	Wired & Wireless
Sustainability certificates	RoHS
Harmonized System (HS) code	84716070