Zebra P4T - Page 19

37537 8VHU*XLGH
19
Figure 7.4-Close the Media Cover
Figure 7.5- Insert Media into Peeler
Section Continues
4. Close the Media Cover:
5HIHUWR)LJXUH
3XOOWKHPHGLDRXWRIWKHSULQWHUDVVKRZQDW´µ
&ORVHWKHPHGLDFRYHUDVVKRZQDW´µHQVXULQJWKDWLWODWFKHV
VHFXUHO\LQWRSODFH
7XUQWKHSULQWHURQRUSUHVVWKH)HHGEXWWRQLIWKHSULQWHULV
DOUHDG\RQ
7KHSULQWHUZLOODGYDQFHDVKRUWVWULSRIPHGLDDQGZLOOWKHQ
EHUHDG\IRUSULQWLQJ
5. Using the Label Peeler
Optional Step for label stock only
5HIHUWR)LJXUH
7KHODEHOSHHOHUIHDWXUHDOORZVDXWRPDWLFVHSDUDWLRQRIWKHSULQWHG
ODEHOIURPLWVEDFNLQJ
,I\RXZLVKWRXVHWKHODEHOSHHOLQJIHDWXUHUHPRYHHQRXJK
ODEHOVIURPWKHPHGLDUROOWRFUHDWHDOHDGHUDSSUR[LPDWHO\µ
>PP@ORQJ
$OLJQWKHPHGLDDVLWHPHUJHVIURPWKHSULQWKHDGZLWKWKH
LQGH[PDUNVRQWKHWRSFRYHUWRHQVXUHLWZLOOSDVVWKURXJK
WKHSHHOHUDVVHPEO\ZLWKRXWZULQNOLQJ
)HHGWKHOHDGHU\RXFUHDWHGLQVWHSRYHUWKHSHHOHUEDUDQG
LQWRWKHSHHOHUDVVHPEO\
3XVK RQ WKH SHHOHU DVVHPEO\ ZKHUH VKRZQ LQ )LJXUH 
,QVHUWWKHOHDGHULQWRWKHODEHOSHHOHUDVVKRZQDQGSXVKRQ
WKHPHGLDUROOXQWLOLWHPHUJHVIURPWKHVORWDWWKHUHDURIWKH
SHHOHUDVVHPEO\
7XUQWKHSULQWHURQRUSUHVVWKH)HHGEXWWRQLIWKHSULQWHULV
DOUHDG\RQ
7KHSULQWHUZLOODGYDQFHDVKRUWVWULSRIPHGLDDQGZLOOWKHQ
EHUHDG\IRUSULQWLQJ
Close Media
Cover
3. Feed the leader over
the peeler bar and into
the printer if you will be
peeling labels as you
print.
4. Press down on Peeler
Assembly where shown
and slide the media until it
emerges .
Peeler Bar.
2. Align the edge of the
leader with the index marks
on the top cover to ensure it
will pass through the peeler
without wrinkling.
Peeler Assembly.
Pull Media out of the
Printer. Use alignment
marks on the cover to
ensure alignment.
1. Remove enough
labels from the media
roll to create a 4” [100
mm] leader.
Printer Preparation
pg. 7
Connecting the
Printer pg. 27
Radio Regulatory
Information pg. 31
RP4T Printers pg.
35
Maintenance pg. 36
Troubleshooting pg.
38
Specications pg.
43
Appendices pg. 46 Index pg. 52
P4T Overview-
pg. 5
Manual
Introduction pg. 4