EasyManua.ls Logo

ZENEC ZE-NC4121D - User Manual

ZENEC ZE-NC4121D
4 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MOUNTING INSTRUCTIONS HYUNDAI iX35
ZE
-
N C 4 121D

Questions and Answers

  • C
    cheyennejamesAug 14, 2025
    Why is there no sound coming from my ZENEC Car Video System?
    • C
      Cassidy JonesAug 15, 2025
      If your ZENEC Car Video System produces no or low audio output, there might be several reasons: * The audio output connection may be improperly connected, so you should check the wiring and correct it. * The volume might be set too low, so increase the volume level. * The speakers could be damaged, requiring replacement. * It's possible that only one channel is playing, in which case, check the balance and fader adjustments. * Speaker wiring might be in contact with a metal part of the car; insulate all speaker wiring connections or replace the speaker cable. * The mute function may be activated; turn off the mute function.
  • B
    Bradley CrawfordAug 17, 2025
    How to fix ZENEC Car Video System that will not power on?
    • S
      Stacey DaughertyAug 17, 2025
      If your ZENEC Car Video System unit will not power on, it could be due to a blown fuse. Check the radio fuse and the car battery fuse, and install new fuses with the correct rating if necessary. It could also be caused by illegal operation of the system. In that case, press the RESET button.
  • R
    Richard GoodwinAug 21, 2025
    What to do if my ZENEC Car Video System has no image?
    • T
      thoffmanAug 21, 2025
      If your ZENEC Car Video System displays no image, ensure that the parking brake is engaged. Stop the vehicle in a safe place and apply the parking brake. Also, check if the "Monitor off" function is activated. If so, touch the monitor to activate the display.
  • J
    Jennifer HerreraAug 25, 2025
    Why does my ZENEC Car Video System have poor sound quality?
    • M
      Maria SweeneyAug 26, 2025
      If your ZENEC Car Video System has poor sound quality or distortion, it could be due to using an unauthorized disc. Use original discs only. It may also be caused by speaker power rating not compatible with unit, so connect proper speakers. A shorted speaker could also be the cause, so check speaker connections.
  • B
    Billy TaylorAug 28, 2025
    Why is the station searching weak on my ZENEC Car Video System?
    • J
      james52Aug 28, 2025
      If you are experiencing weak station searching with your ZENEC Car Video System, ensure the auto antenna is properly connected. Also, check if the REG function is activated and turn it off. Finally, make sure the AF function is activated.
  • V
    Victoria HarveyAug 31, 2025
    What to do if disc does not play back on ZENEC Car Video System?
    • J
      Joshua ParkerAug 31, 2025
      If your ZENEC Car Video System disc does not play back, it could be due to several reasons: * The disc is warped or scratched; use a disc in good condition. * The disc is dirty or wet; clean the disc with a soft cloth. * An incompatible disc is being used; use a compatible disc. * The disc rating exceeds the parental lock rating limit; change the parental lock settings to a lower restriction. * The disc region code is not compatible with the unit; use a disc with the proper region code. * The disc is inserted upside down; insert the disc with the label side up.
  • J
    Jose RobinsonSep 3, 2025
    How to fix prolonged image on ZENEC Car Video System?
    • E
      Ernest WeberSep 3, 2025
      If your ZENEC Car Video System shows a prolonged image or improper height/width ratio, this is due to an improper aspect ratio setup. Use the correct aspect ratio setting.
  • J
    Johnny JacksonSep 6, 2025
    Why are the ID3 tags shown incorrectly on my ZENEC Car Video System?
    • B
      brendaperezSep 6, 2025
      If the ID3 tags are shown incorrectly on your ZENEC Car Video System, it is because the message is longer than the LCD can display or the ID3 tag is not compatible. Use proper ID3 tag information.
  • J
    John ClaySep 10, 2025
    What to do if I cannot insert disc in ZENEC Car Video System?
    • R
      Rebecca MillerSep 10, 2025
      If you cannot insert a disc into your ZENEC Car Video System, it is likely because there is already a disc inside the unit. Eject the current disc and then insert the new one.

ZENEC ZE-NC4121D Specifications

General IconGeneral
Display Size6.2 inches
Resolution800 x 480 pixels
BluetoothYes
Radio TunerFM/AM
NavigationYes
SD Card ReaderYes
DVD PlayerYes
Amplifier Output4 x 50 Watts
TouchscreenYes
Video PlaybackYes
Audio PlaybackYes
Steering Wheel ControlYes
Rear View Camera InputYes
Operating SystemWindows CE

Related product manuals