Zenoah BC4350FW - User Manual

Zenoah BC4350FW

15 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

G

B

BC4350FW

BRUSHCUTTERS

115 44 10-38 (107)

OWNER’S MANUAL

•Before using our brushcutter, please

read this manual carefully to understand

the proper use of your unit.

• Keep this manual handy.

Caution

Table of Contents

Questions and Answers

J
Jennifer ThomasAug 9, 2025
How to troubleshoot Zenoah Brush Cutter if engine does not start?
- C
  caleb42Aug 9, 2025
  If your Zenoah Brush Cutter engine won't start, there are several potential causes. It could be due to bad or deteriorated fuel, in which case you should replace it with normal fuel. Another possibility is excessive fuel sucking; try opening the choke and throttle fully, then repeatedly pull the rope. A clogged muffler exhaust vent can also prevent starting, so clean the muffler. Finally, check for contaminated spark plug electrodes or a short-circuited/broken wire; clean the electrodes or replace the spark plug.
H
Haley HudsonAug 14, 2025
What to do if Zenoah BC4350FW engine does not accelerate?
- K
  Kelsey OchoaAug 14, 2025
  If your Zenoah Brush Cutter engine isn't accelerating properly, it might be due to bad or deteriorated fuel. Replacing it with normal fuel may resolve the issue. Alternatively, a clogged muffler exhaust vent could be the culprit, so cleaning the muffler is advisable.
S
Stephanie AlvaradoAug 19, 2025
Why my Zenoah Brush Cutter has deterioration of fuel consumption?
- D
  David MayAug 19, 2025
  Increased fuel consumption in your Zenoah Brush Cutter could stem from a few issues. A clogged air cleaner could be the cause, so cleaning the air cleaner is recommended. A blunt blade will also increase fuel consumption, so replace the blade if necessary. Insufficient lubrication of the gear case can also lead to this issue, so supply grease to the gear case.
C
christianwaltonAug 25, 2025
What causes abnormal vibration in Zenoah Brush Cutter?
- L
  lorigomezAug 25, 2025
  If your Zenoah Brush Cutter experiences abnormal vibration, it may be due to deformation or damage of the blade. Replacing the blade should solve this issue.
B
Brent DavidAug 29, 2025
What to do if Zenoah Brush Cutter engine stalls when throttle is returned to its original position?
- K
  Kathy RossAug 29, 2025
  If the engine of your Zenoah Brush Cutter stalls when returning the throttle to its original position, it's likely that the idling revolution speed is too low. Readjusting the idling adjustment screw should resolve this issue.
J
Jasmine RileySep 3, 2025
Why does the engine rotation speed change on my Zenoah BC4350FW?
- L
  laurawardSep 4, 2025
  If the engine rotation speed of your Zenoah Brush Cutter changes erratically, it might be due to a clogged fuel filter. Cleaning or replacing the fuel filter is the suggested solution.

Zenoah BC4350FW Specifications

General

Shaft Type	Straight
Starter System	Recoil
Fuel Mix Ratio	50:1
Engine Type	Air-cooled, 2-stroke
Power Output	1.6 kW
Cutting Width	430 mm

Related product manuals

Zenoah BC430DWM

Zenoah BC4300FWM

Zenoah BC4401DW

Preview: Zenoah BC2200DL

Zenoah BC2200DL

Preview: Zenoah BC3450DW

Zenoah BC3450DW

Zenoah BC3500DLM

Preview: Zenoah BCZ4505CL

Zenoah BCZ4505CL

Preview: Zenoah BCZ4000DW

Zenoah BCZ4000DW

Zenoah BC3401DLM

Zenoah BCZ4200CL

Zenoah BCZ4500/5000CL

Preview: Zenoah BRUSHCUTTERS BCZ4000DL

Zenoah BRUSHCUTTERS BCZ4000DL