What to do if my ZENROLL C1 Scooter does not work?
If your ZENROLL Scooter isn't working, there are several potential causes: * **Insufficient battery power:** Charge the battery. * **Battery not fully seated:** Install the battery correctly. * **Battery aging or damage:** Replace the battery. * **Improper turn on sequence:** Ensure you are using the correct sequence to turn on the e-bike.
Why is my ZENROLL C1's motor not responding after powering on?
If the motor of your ZENROLL Scooter isn't responding when powered on, it could be due to: * A loose battery connection: Reconnect the battery. * Loose wiring: Reconnect or repair the wiring. * A loose or damaged throttle: Tighten or replace the throttle. * A damaged motor: Repair or replace the motor.
Why is my ZENROLL C1's range reduced?
A reduced range in your ZENROLL Scooter can stem from several factors: * Low tire pressure: Adjust tire pressure. * Low or faulty battery: Check connections or charge the battery. * Demanding riding conditions: Assist with pedals or adjust your route if you're encountering too many hills, headwinds, braking, or excessive load. * Battery issues: Balance or replace the battery if it has been discharged for a long period without regular charges, is aged, damaged, or unbalanced. * Brakes rubbing: Adjust the brakes. * Low temperature: Warm the battery above 32°F (0°C).
Why does my ZENROLL C1 have irregular acceleration?
Irregular acceleration in your ZENROLL Scooter could be due to insufficient battery power. Try charging or replacing the battery.
Why is the top speed of my ZENROLL Scooter reduced?
If your ZENROLL Scooter's top speed is reduced, the cause might be insufficient battery power. Try charging or replacing the battery.
What to do if pedal assist does not work on ZENROLL C1 Scooter?
If the pedal assist on your ZENROLL Scooter isn't working, the speed sensor may be damaged. Consider repairing or replacing it.
What to do if throttle does not work on ZENROLL C1 Scooter?
If the throttle on your ZENROLL Scooter isn't working, it could be loose or damaged. Consider replacing it.
What to do if display does not light on ZENROLL C1 Scooter?
If the display on your ZENROLL Scooter doesn't light up, it might be due to poor contact of the display line. Try reconnecting the display line.
What to do if gear does not work well on ZENROLL C1?
If the gear on your ZENROLL Scooter isn't working well, the rear derailleur might be mismatched. Try adjusting the rear derailleur.
What to do if brake does not work well on ZENROLL Scooter because the brake disc is bent?
If the brake on your ZENROLL Scooter isn't working well because the brake disc is bent, try adjusting the brake disc.
Verify electrical systems and brakes are functioning correctly before each ride.
Read manual, avoid water, do not modify, check safety labels, obey laws, keep body parts clear.
Check brakes, tires, guards. Do not exceed the 330 lbs maximum load rating.
Climb grade 30°, max load 330 lbs, max speed 25 mph, 500W motor.
Instructions for charging the battery while it's on or off the bike.
Use only the specified charger. Charge in dry, safe indoor locations away from flammables.
Avoid unattended charging, leaving charger plugged in when full, and charging damaged batteries.
Power assist engages with pedaling. Apply light force for smooth assistance.
Do not submerge, alter, short-circuit, or misuse the battery.
Check battery, connections, throttle, motor, and speed sensor for potential causes.
Always wear a helmet and comply with all local cycling and eBiking regulations.
Inspect for loose parts, check tire pressure, brakes, and secure latches before every ride.
Adhering to the 330 lbs limit is crucial for safety, warranty, and bike integrity.
General| Battery Capacity | 36V 7.5Ah |
|---|---|
| Charging Time | 4-5 hours |
| Foldable | Yes |
| Max Speed | 25 km/h (15.5 mph) |
| Max Load | 120 kg (265 lbs) |
| Tire Size | 8.5 inches |
| Brake Type | Rear disc brake + electric brake |
To Next Page