How to clean safety grill of Zephyr Typhoon AK2136?
The self-clean feature on your Zephyr Ventilation Hood only cleans the internal housing. Remove the safety grill to clean it in the dishwasher and clean all surfaces periodically as instructed.
Why does cooking smoke dissipate before reaching the Zephyr Typhoon AK2136?
If cooking fumes and smoke dissipate before reaching the Zephyr Ventilation Hood blower, there are several potential causes. Ensure you are using a damper-type sidewall cap. Reduce the number of elbows and the length of ductwork, or increase the duct size. Verify that all joints are properly connected, sealed, and taped. Confirm that the unit is installed at the recommended height and covers the entire cooking area. Also, ensure that doors and windows are closed to avoid airflow disruption and that blowers are set to high speed during heavy cooking.
Why is my Zephyr Typhoon AK2136 Ventilation Hood so noisy?
Zephyr Ventilation Hood blowers are designed to perform up to 850 cfm. A properly functioning motor should be relatively quiet. However, the suction can generate noise levels up to 6 sones when both blowers are on maximum speed. Use maximum speed only when necessary, such as during heavy pan-frying or wok cooking. Lower speeds are sufficient for moderate cooking like steaming or broiling.
Why does my Zephyr Ventilation Hood vibrate when the blowers are on?
Vibration in your Zephyr Ventilation Hood when the blowers are on may be due to improper securing of the unit to the cabinet, or the cabinet itself might need to be further secured to the wall studs.
What to do if my Zephyr Typhoon AK2136 doesn't work after installation?
If your Zephyr Ventilation Hood isn't working after installation, check that the unit is plugged in, power is turned on, and all electrical wiring is properly connected.
Why does my Zephyr Typhoon AK2136 Ventilation Hood blower seem weak?
Weak blowers in your Zephyr Ventilation Hood may be due to clogged tubes connected to the internal housing or the hood not being level. Try unclogging the tubes or reinstalling the hood.
What to do if something is spinning inside my Zephyr Ventilation Hood?
If something seems loose and is spinning inside your Zephyr Ventilation Hood when the blowers are on, there might be foreign particles in the discharge opening or debris from old ductwork. Disconnect the ductwork to inspect and remove any foreign particles.
How to fix the light on my Zephyr Typhoon AK2136 Ventilation Hood?
If the light in your Zephyr Ventilation Hood isn't working, the bulb may need replacement. The bulb could have been damaged during shipping, so try replacing it.
What to do if Zephyr Typhoon AK2136 light is on but blowers aren't turning?
If the light is on but the blowers are not turning, or seem to be scraping, the blower blade unit of your Zephyr Ventilation Hood might be mounted too low and scraping. Loosen the hex screw on the blade unit and adjust it to the proper height.
Why is no grease collected in the clean cups of my Zephyr Typhoon AK2136 Ventilation Hood?
Grease flow varies depending on the amount, methods, and types of cooking. If you frequently pan-fry and steam, the vapor from the steam will liquefy accumulated grease in the internal housing, causing it to flow into the clean cups of your Zephyr Ventilation Hood.
Provides an overview of the touch control module and its functions.
Details on operating blowers and lights, including speed adjustment and light functions.
Explains how to set the automatic shut-off timer for the range hood.
Specifies minimum clearances and duct size requirements for proper installation.
Illustrates duct opening dimensions and electrical connection points.
Guide on using the provided template for marking drill locations.
Step-by-step instructions for mounting and electrical hookup.
Guides for converting the hood to vertical or rear discharge methods.
Explains the automatic self-cleaning function of the range hood.
Steps for cleaning safety grills, cups, surfaces, and useful cleaning tips.
Guide on how to replace the halogen light bulbs.
Addresses common problems like unit not working, blower noise, and weak blowers.
Solutions for fume dissipation, ducting issues, and installation height problems.
General| Speeds | 3 |
|---|---|
| Number of Fan Speeds | 3 |
| Material | Stainless Steel |
| Color | Stainless Steel |
| Vent Size | 6 inches |
To Next Page