EasyManuals Logo

ZIEHL-ABEGG ZETADYN 4C User Manual

ZIEHL-ABEGG ZETADYN 4C
204 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #132 background imageLoading...
Page #132 background image
14.5.2 Block function
Blocks the controller if certain errors occur several times is succession. The errors must occur in
directly consecutive travel tests. The fault counter is set to 0 when performing a trouble-free run.
The following block functions can be set in the Monitoring / MOD_ST menu:
Fix 2 Sec.: No blocking function, the output congured on "ST" drops for 2 seconds during a
malfunction and then increases again (speed preset V_x must be switched off)
Lock n.3: Lock function after 3 malfunctions. Output "ST" remains dropped after the 3rd error
Lock n.2: Lock function after 2 malfunctions. Output "ST" remains dropped after the 2rd error
Lock n.1: Lock function after 1 malfunction1. Output "ST" remains dropped after the 1st error
Errors which lead to disabling of the ZETADYN 4 are marked by a dot in the S column.
14.5.3 Notes 0xx
Information about:
Error memory content
Changes in the operating conditions
Application of special frequency inverter functions
Note-No. Note text Description M S
N0 Memory empty EEPROM is empty
N010 Update software Software update was carried out
Additional information: Version of the new software
N020 MOT_TYP changed Motor type in "Motor name plate" was changed
N077 ST_LST: locked Five faults occurred in direct succession
Fault memory is blocked
Additional information: indicates the most recent fault
The fault counter is set to 0 when performing a trouble-free run.
N080 Mode: EVA ->Norm Switchover from evacuation to normal mode was implemented
N081 Mode: Norm ->EVA Switchover from normal to evacuation to mode was implemented
N082 Mode:ParaChange The parameter set was changed
N085 Mode: Safety Br Safety brake function was implemented
N086 Mode:Enc.Adj.MB Encoder-alignment with closed brakes was carried out
N087 Mode:Encoder-Adj. Manual encoder offset was carried out
N088 Mode:Encoder-Check The encoder offset alignment was checked
14.5.4 Error 1xx
Hardware conguration error
Software error
Error no. Error text Error cause M S
100 Serial no. missing
Frequency inverter/CU does not have a serial number, e.g. after a component
replacement
101 System-Error
A defective internal component was identied during a self-test of the fre-
quency inverter
110
120
CU: No ID
CU ID no. was not detected:
CU is not present or its ID EEPROM does not reply
111 CUSH: No ID
Shunt ID no. was not detected:
Shunt module is not present or its ID EEPROM does not reply
113
123
CUEE: No ID
ID no. of the extension card for the rotary encoder was not detected: extension
module is not present or its ID EEPROM does not reply
115
125
SP: No ID
Switching power supply ID no. was not detected: Switching power supply is not
present or its ID EEPROM does not reply
116
126
PP: No ID
Power print ID no. was not detected:
Power print is not present or its ID EEPROM does not reply
Translation of the original operating instructions
ZETADYN 4C Error diagnosis
R-TBA12_01-GB 1415 Part.-No. 00163371-GB
132
/204

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the ZIEHL-ABEGG ZETADYN 4C and is the answer not in the manual?

ZIEHL-ABEGG ZETADYN 4C Specifications

General IconGeneral
BrandZIEHL-ABEGG
ModelZETADYN 4C
CategoryDC Drives
LanguageEnglish

Related product manuals