To Next PageTo Next PageWhat to do if 8Err78 appears on the ZIEHL UFR1001E Relays display after reconnection attempts?
If '8Err78' appears after two automatic reconnection attempts and LEDs K1 and/or K2 are lit, it indicates that feedback contacts are not correctly connected. Check the connection of the feedback contacts, set the turn-on time of the section switch under '8trel.8', and then perform a reset by interrupting the control voltage for more than 5 seconds.
What does 8stby8 mean on my ZIEHL Measuring Instruments display?
If 'stby' is displayed on your ZIEHL Measuring Instruments, it indicates that the device is in standby mode because E1-E2 is active. Check the parameter 'vsr'.
What to do if 8EEEE8 or 8-EEE8 appears on my ZIEHL UFR1001E display?
If you see '8EEEE8' or '8-EEE8' on the display, it means the measured voltage, frequency, or vector surge is outside the acceptable range. Ensure that your measurements are within the specified limits for your ZIEHL Relays.
What to do if a time expires in the display of ZIEHL Measuring Instruments?
To resolve the issue of time expiring on the display of ZIEHL Measuring Instruments, wait until the time has expired; depending on the setting, this may occur several times consecutively.
What does 8Err48 mean on ZIEHL Measuring Instruments and how can I fix it?
If 'Err4' appears on the display of ZIEHL Measuring Instruments, it signals a tolerance error, which is an internal measurement value deviation between both channels. You can attempt to resolve this by performing a reset of the interrupt control voltage for >5s. If 'Err5' appears, check for long cables connected to terminals E or Y and whether they are routed through an environment with interference.
Why are '8 8' and LED Q3 on with good range on my ZIEHL UFR1001E?
If '8 8' and LED Q3 (f>) are on, and the reading is in good range on your ZIEHL Relays, the hysteresis for 8 8 might be incorrect. Check the hysteresis for reset point 50,05 Hz.
What does '8Err98' on ZIEHL UFR1001E Relays mean and how to fix it?
If '8Err98' appears on the display of your ZIEHL Relays, it indicates a configuration error. To solve this, reset the device to its factory settings.
What to do if '8Err48' appears on the display of ZIEHL UFR1001E?
If '8Err48' appears on the display of your ZIEHL Relays, it means there's too high an internal measurement deviation between the two measuring channels. To fix this, perform a reset by interrupting the control supply voltage for more than 5 seconds.
What does it mean if '8Err78' appears with a lit LED 'd' on ZIEHL UFR1001E?
If '8Err78' appears on the display of your ZIEHL Relays and the LED 'd' of the faulty output circuit is lit, it indicates an issue with the feedback contacts. If feedback contacts are not connected, set 'trel.8' to 'off'. If they are connected, check the connection. Also, adjust the turn-on time of the section switch under 'trel.8'. Perform a reset by interrupting the control supply voltage for more than 5 seconds.
Why are implausible voltage values displayed on ZIEHL Relays?
If you are getting implausible voltage values on your ZIEHL Relays, it might be because 'Pr' is selected with 'N', but 'N' is not connected. To fix this, either select 'Pr' without 'N' or connect 'N'.
General| Frequency | 50/60 Hz |
|---|---|
| Pick-up value | Adjustable |
| Response delay tv | Adjustable |
| Tripping delay ta | Adjustable |
| Mounting | DIN rail |
| Housing material | Plastic |
| Operating temperature range | -20°C to +60°C |
| Protection class | IP20 |
| Operating temperature | -20°C to +55°C |
| Hysteresis | Adjustable |
