What to do if Zodiac Vacuum Cleaner does not stay firmly on the pool floor?
If your Zodiac Vacuum Cleaner isn't staying firmly on the pool floor, it might be due to a few reasons. First, repeat the immersion steps to remove any air trapped in the appliance's casing. Also, clean the filter if it's full or dirty, and replace it if it remains clogged after cleaning. If the impeller is damaged, no solution is provided.
How to untangle the cable of Zodiac CNX 20?
If your Zodiac Vacuum Cleaner cable gets tangled, unroll as much cable as possible into the pool and lay the remainder by the pool side.
What does a red dot mean in the 'My systems' list for Zodiac CNX 20?
If you see a red dot in the 'My systems' list for your Zodiac Vacuum Cleaner, it could mean the appliance isn't plugged in or connected to the home Wi-Fi network. If the dot is red when the control box is plugged in and the Bluetooth/Wi-Fi icons are lit, refresh the screen. If the dot turns green, the appliance is ready for use.
What to do if Zodiac CNX 20 update failed?
If your Zodiac Vacuum Cleaner displays 'Update failed or incomplete', disconnect and reconnect the control box to restart the update. If the error persists, contact a retailer.
How to troubleshoot connection error on Zodiac CNX 20 Vacuum Cleaner?
If your Zodiac Vacuum Cleaner displays 'Connection error', check the status of the Bluetooth/Wi-Fi LEDs on the control box and follow the steps described in the table "5.3 I Troubleshooting the connection to the iAquaLink™ app."
What to do if my Zodiac CNX 20 Vacuum Cleaner is out of the water?
If your Zodiac Vacuum Cleaner is out of the water, turn it off, thoroughly clean the filter, put it back in the water (shaking to release air bubbles), and restart the cycle. If the problem persists, contact your retailer for assistance.
General| Type | Robotic Pool Cleaner |
|---|---|
| Pool Type | In-ground |
| Wet Mopping | No |
| Auto Recharge | No |
| Virtual Boundary | No |
| Multi-floor Mapping | No |
| Model | CNX 20 Series |
| Battery Type | Rechargeable |
| Connectivity | No |
Details the components and parts of the robotic cleaner and its accessories.
Provides detailed technical specifications, dimensions, and included parts for different models.
Explains how the robotic cleaner operates autonomously and cleans pool areas.
Outlines necessary pool conditions, water parameters, and pre-cleaning steps.
Provides instructions on how to safely immerse the cleaner into the pool water.
Details how to connect the cleaner to its base unit for operation.
Explains the correct and safe procedure for connecting the cleaner to the power supply.
Describes the functions of the control box keys and indicator lights.
Guides users on selecting cleaning modes and launching the cleaning cycle.
Explains the safe method for removing the cleaner from the pool, with or without Lift System.
Covers filter cleaning, cable management, and proper storage after use.
Steps for initial setup and connection of the cleaner to the iAquaLink™™ app.
Details remote control, progress monitoring, and other app features for iQ models.
Instructions for using the smartphone as a remote control via the app's joystick mode.
How to activate the Lift System function remotely via the iAquaLink™™ app.
Explains how error messages are displayed and how to address them using the app.
Information on how to access and modify the cleaner's settings through the app.
Instructions for cleaning the exterior of the robotic cleaner.
Detailed steps for cleaning the filter to ensure optimal performance.
Procedure for accessing and cleaning the impeller to ensure proper function.
Guide on how to identify worn brushes and replace them correctly.
Troubleshooting guide for common issues like incomplete cleaning or poor floor grip.
Explanation of control box LED indicators and corresponding troubleshooting steps.
Steps to resolve issues with connecting the cleaner to the iAquaLink™™ app and Wi-Fi.
To Next Page
