ZOOM G1/G1X
26
Special Features of G1X
This section explains features and operating steps that are unique to the G1X.
[PEDAL ASSIGN] key operation
The top panel of the G1X has a [PEDAL
ASSIGN] key. Besides the method described on
page 17, the module to be controlled by the pedal
can be selected with this key.
1. In play mode or edit mode, press the
[PEDAL ASSIGN] key to select the
control target module.
The module currently selected as control target is
indicated by the row of LEDs above the [PEDAL
ASSIGN] key.
2. Store the patch as required.
3. In play mode, select the patch and
operate the expression pedal.
The respective parameter changes in real time.
4. To toggle the module assigned to the
pedal between on and off, briefly
push the pedal fully down.
When the module is off, the respective LED
above the [PEDAL ASSIGN] key flashes. This
function can also be used in edit mode.
Adjusting the expression pedal
The expression pedal of the G1X can be
readjusted as necessary. If the effect change
seems insufficient when pushing the pedal down,
or if the volume or tone changes excessively
even when the pedal is only lightly pushed,
adjust the pedal as follows.
1. Hold down the [PEDAL ASSIGN] key
while turning power to the G1X on.
The indication "dn" appears on the display.
2. Fully raise the expression pedal and
press the [STORE] key.
The indication "UP" appears on the display.
3. Push the expression pedal fully down
and release it.
4. Press the [STORE] key once more.
The adjustment is complete, and the unit returns
to the play mode. If the indication "Er" is shown,
repeat the procedure from step 2.
ll out
Pedal is inactive
Volume
COMP/EFX module
DRIVE module
MODULATION module
DELAY module
REVERB module
Push strongly, so
that pedal touches
here
When foot is lifted,
pedal returns slightly
ZOOM G1/G1X
27
Effect types 54
Effect modules max. 8 simultaneous modules
Patch memory User area: 10 patches x 4 banks = 40
Preset area: 10 patches x 4 banks = 40
Total 80 patches
Sampling frequency 96 kHz
A/D converter 24 bit, 128 times oversampling
D/A converter 24 bit, 128 times oversampling
Signal processing 32 bit
Frequency response 20 Hz – 40 kHz +1.0 dB -4.0 dB (10-kilohm load)
Display 2-digit 7-segment LED
Input Standard mono phone jack
Rated input level -20 dBm
Input impedance 470 kilohms
Output Standard stereo phone jack (doubles as line/headphone jack)
Maximum output level Line +3 dBm
(output load impedance of 10 kilohms or more)
Phones 20 mW + 20 mW (into 32-ohm load)
Control input For FP02/FP01 or FS01 (G1 only)
Power requirements
AC adapter 9 V DC, 300 mA (center minus plug) (ZOOM AD-0006)
Batteries G1/G1X Four IEC R6 (size AA) batteries, approx.
12 hours continuous operation (alkaline batteries)
Dimensions G1 155 mm (D) x 136 mm (W) x 52 mm (H)
G1X 155 mm (D) x 234 mm (W) x 52 mm (H)
Weight G1 350 g (without batteries)
G1X 600 g (without batteries)
Options Expression pedal FP01/FP02 or Foot switch FS01 (G1 only)
Specifications
Troubleshooting
● No power
Refer to "Turn power on" on page 6.
● Reverb effect does not operate
While a rhythm pattern is playing, the reverb
effect is not available. Stop the rhythm pattern
first (→ p. 11).
● Patches cannot be switched
Has the method for calling up patches been
changed to "pre-select" (→ p. 16)? Turn
power off and then on again to reset the unit to
normal operation.
● High level of noise
Is ZOOM AC adapter being used? Be sure to
use only an adapter for 9 V DC, 300 mA with
center minus plug (ZOOM AD-0006).
● Battery life is short
Are manganese batteries being used?
Continuous operation time is 12 hours with
alkaline batteries.
To Next Page
Loading...
Need help?
General
