Zoom MultiStomp MS-50G Parameter Guide

10
Effect Types and Parameters
11
StompDly By turning the feedback up on this stomp-style delay, you can make it self-oscillate.
Knob1 Knob2 Knob3
Page01
E.LVL 0–120 F.B 0–100 Time 1–600
Adjusts amount of effec t sound
mixed with original sound.
Adjusts the feedback amount. Sets the delay time.
Page02
Sync OFF,
– x8 Mode MONO, STR Tail OFF/ON
Activates tempo sync.
Sets output to mono or stereo (STR).
When stereo, effect sound is output
from L channel and unchanged input
sound is output from R channel.
When ON, effect sound continues
even after effect is turned off. When
OFF, effect sound stops right when
effect is turned off.
Page03
HiDMP 0–10
Adjusts the treble attenuation of the
delay sound.
HD Hall This is a dense hall reverb.
Knob1 Knob2 Knob3
Page01
PreD 1–200 Decay 0–100 Mix 0–100
Adjusts the delay between input of
the original sound and start of the
reverb sound.
Sets the duration of the reverberations.
Adjusts the amount of effected sound
that is mixed with the original sound.
Page02
LoDMP 0–100 HiDMP 0–100 Tail OFF/ON
Adjusts low frequency damping in
reverb sound.
Adjusts high frequency damping in
reverb sound.
When ON, effect sound continues
even after effect is turned off. When
OFF, effect sound stops right when
effect is turned off.
Hall This reverb effect simulates the acoustics of a concert hall.
Knob1 Knob2 Knob3
Page01
Decay 1–30 Tone 0–10 Mix 0–100
Sets the duration of the reverberations. Adjusts the tone.
Adjusts the amount of effected sound
that is mixed with the original sound.
Page02
PreD 1–100 Level 0–150 Tail OFF/ON
Adjusts the delay between input of the
original sound and start of the reverb sound.
Adjusts the output level.
When ON, effect sound continues
even after effect is turned off. When
OFF, effect sound stops right when
effect is turned off.
Room This reverb effect simulates the acoustics of a room.
Knob1 Knob2 Knob3
Page01
Decay 1–30 Tone 0–10 Mix 0–100
Sets the duration of the reverberations. Adjusts the tone.
Adjusts the amount of effected sound
that is mixed with the original sound.
Page02
PreD 1–100 Level 0–150 Tail OFF/ON
Adjusts the delay between input of the
original sound and start of the reverb sound.
Adjusts the output level.
When ON, effect sound continues
even after effect is turned off. When
OFF, effect sound stops right when
effect is turned off.
Spring This reverb effect simulates a spring reverb.
Knob1 Knob2 Knob3
Page01
Decay 1–30 Tone 0–10 Mix 0–100
Sets the duration of the reverberations. Adjusts the tone.
Adjusts the amount of effected sound
that is mixed with the original sound.
Page02
PreD 1–100 Level 0–150 Tail OFF/ON
Adjusts the delay between input of the
original sound and start of the reverb sound.
Adjusts the output level.
When ON, effect sound continues
even after effect is turned off. When
OFF, effect sound stops right when
effect is turned off.

Zoom MultiStomp MS-50G Specifications

General

Simultaneous Effects	6
Display	LCD
Sampling Frequency	44.1 kHz
A/D Conversion	24-bit
D/A Conversion	24-bit
Patches	50
Input	1/4"
Output	1/4"
Power	9V DC
Weight	350 g (without batteries)
Frequency Response	20Hz - 20kHz
Power Supply	Batteries: AA/LR6 battery x 2
Battery Life	Approx. 6 hours (alkaline batteries)
Effect Types	Delay, Reverb, Modulation, Distortion, EQ, Filter, Dynamics