Why does my zortrax Inventure 3D Printers says '#196 Insufficient cooling of the printer'?
If your Zortrax 3D Printer shows '#196 Insufficient cooling of the printer', it means the room temperature is too high, which may cause printing problems. Ensure the print room temperature is below 40° C/104° F.
What to do if my Zortrax 3D Printers says '#178 Support material jam error. Extruder failure due to overheating'?
If your Zortrax 3D Printer displays '#178 Support material jam error. Extruder failure due to overheating', it could be due to high ambient temperature or a blockage in the extruder. Ensure the room temperature is below 40° C/104° F and allow the printer to cool down. Also, try unloading and reloading the support material.
What to do if my zortrax Inventure says '#177 Support material jam error. Cartridge failure'?
If your Zortrax 3D Printer shows '#177 Support material jam error. Cartridge failure', it means the support material is blocked in the material duct or tangled within the cartridge. Unload the support material and check if it can be easily slid out of the cartridge. If not, load a new support material.
What to do if my zortrax Inventure says '#176 Model material jam error. Cartridge failure'?
If your Zortrax 3D Printer displays '#176 Model material jam error. Cartridge failure', it means the model material is blocked in the material duct or tangled within the cartridge. Unload the model material and check if it can be easily slid out of the cartridge. If not, load a new model material.
What to do if my Zortrax 3D Printers shows '#162 The support material cartridge is empty'?
If your Zortrax 3D Printer shows '#162 The support material cartridge is empty', it means that the support material cartridge has run out of material. Replace the empty cartridge with a different or a new support material cartridge.
Why does my zortrax Inventure 3D Printers say '#158 Wrong material type for this model'?
If your Zortrax 3D Printer shows '#158 Wrong material type for this model', it means the wrong model material has been installed or the file was prepared for a different material type. Replace the model material with the correct one, prepare the file for the proper model material type, or install a different model material cartridge.
What to do if my Zortrax 3D Printers says '#141 Extruder Lower fan failure'?
If your Zortrax 3D Printer displays '#141 Extruder Lower fan failure', it indicates that the extruder lower fan is either disconnected or incorrectly installed. Check if the lower extruder fan is properly installed. If the problem persists, replace the lower extruder fan.
What to do if my Zortrax 3D Printers says '#140 Extruder Upper fan failure'?
If your Zortrax 3D Printer shows '#140 Extruder Upper fan failure', the extruder upper fan is either disconnected or incorrectly installed. Check if the upper extruder fan is properly installed. If the issue persists, replace the upper extruder fan.
What to do if my Zortrax 3D Printers says '#138 Extruder cable disconnected'?
If your Zortrax 3D Printer displays '#138 Extruder cable disconnected', it means the extruder cable is either disconnected, incorrectly installed, or damaged. Check if the extruder cable is properly connected. If there is still a problem, replace the extruder cable.
What to do if my zortrax Inventure says '#137 Build tray missing or not seated properly'?
If your Zortrax 3D Printer shows '#137 Build tray missing or not seated properly', it indicates that the build tray is either missing or incorrectly installed, or there may be a platform cable failure or a lack of calibration points. Try removing and reinstalling the build tray. Check for five calibration points on the build tray. Also, replace the cable under the platform.
General| Nozzle width | 0.4 mm |
|---|---|
| Print technology | Layer Plastic Deposition Plus (LPD PLUS) |
| Printing material | ABS, Acrylonitrile Styrene Acrylate (ASA), Nylon, Polyethylene Terephthalate Glycol (PETG), Polylactic acid (PLA) |
| Layer thickness (max) | 0.3 mm |
| Layer thickness (min) | 0.15 mm |
| Number of print heads | 2 |
| Maximum build size (WxDxH) | 135 x 135 x 130 mm |
| Filament thickness supported | 1.75 mm |
| 3D scanner | No |
| Card reader integrated | Yes |
| Compatible memory cards | SD |
| Product color | Black |
| AC input voltage | 110 / 240 V |
| AC input frequency | 50 / 60 Hz |
| Power consumption (max) | 300 W |
| Storage temperature (T-T) | 0 - 35 °C |
| Operating temperature (T-T) | 15 - 30 °C |
Explains the Layer Plastic Deposition Plus (LPD Plus) technology and the printer's intended applications.
Provides important safety directions for installation, operation, and general precautions.
Covers health, electrical, and mechanical safety measures for printer operation.
Highlights risks like burns and explains warning labels on the device.
Outlines safe practices for storing and transporting the Zortrax Inventure.
Explains the printing process from model preparation to print completion and post-processing.
Lists all the components and accessories included with the Zortrax Inventure.
Identifies and illustrates the key physical parts of the Zortrax Inventure printer.
Defines technical terms and concepts related to Zortrax 3D printing technology.
Step-by-step guide for unboxing and initial setup of the Zortrax Inventure.
Instructions on downloading and installing the latest firmware for the printer.
Explains how to use the printer's interface and navigate through its menus.
Describes the different operating modes indicated by LED lights and sounds.
Step-by-step guide on how to load model and support materials into the printer.
Instructions for calibrating the printer's build platform for optimal printing.
Guide on calibrating nozzle alignment for precise printing results.
Details the process of starting a print and safely removing finished models.
Information about Zortrax certified materials and where to find them.
Guidelines for regular maintenance tasks to keep the printer in good condition.
Information on common issues, error messages, and solutions for the Zortrax Inventure.
Technical specifications and operational characteristics of the Zortrax Inventure 3D printer.
Information on proper disposal of electronic waste and device certifications.
To Next Page
