To Next PageTo Next Page
Need help?Do you have a question about the ZyXEL Communications XMG1915-10EP and is the answer not in the manual?
General| Number of Ports | 10 |
|---|---|
| Port Type | Gigabit Ethernet |
| Power over Ethernet (PoE) | Yes |
| PoE Ports | 8 |
| PoE+ ports | 8 |
| PoE++ ports | 0 |
| PoE Budget | 130 W |
| Total PoE Budget | 130 W |
| Switching Capacity | 40 Gbps |
| Forwarding Rate | 29.76 Mpps |
| Layer | Layer 2 |
| MAC Address Table | 8K |
| Jumbo Frame | Yes |
| Storage Temperature | -40°C to 70°C |
| Product Type | Switch |
| MAC Address Table Entries | 8K |
| Dimensions | 260 mm (W) x 150 mm (D) x 44 mm (H) |
| Weight | 1.1 kg |
| Power Supply | Internal |
| Operating Temperature | 0°C to 50°C |
| Humidity | 5% to 95% (non-condensing) |
| Ports | 8 x 10/100/1000 Mbps PoE+ ports, 2 x 1G SFP slots |
| Jumbo Frame Support | 9KB |
Lists important safety guidelines and precautions to observe before using the Switch.
Explains the grounding procedure for safety and protection against electrical hazards.
Describes the process for accessing the Switch's Web Configurator interface.
Explains how to save current configuration settings to non-volatile memory.
Provides instructions on how to reset the Switch to its factory default settings.
Details the process of creating a VLAN and assigning ports.
Explains how to set the Port VLAN ID (PVID) for incoming untagged frames.
Shows how to configure the management IP address for the Switch.
Provides a tutorial on configuring DHCPv4 snooping for network security.
Offers a tutorial on configuring the Switch to forward DHCP requests.
Configures general settings including system name, location, and time.
Configures default gateway, DNS server, and adds IP domains.
Configures global IPv6 settings, including hop limit and rate limiting.
Views and configures IPv6 interfaces, including activation status.
Configures the link-local address and default gateway for IPv6 interfaces.
Views and configures the interface’s IPv6 global unicast address.
Configures neighbor discovery settings for each IPv6 interface.
Configures router discovery settings for each IPv6 interface.
Configures the Switch’s IPv6 prefix list for each interface.
Views and configures static IPv6 neighbor entries in the Switch’s neighbor table.
Configures the Switch’s DHCP settings when acting as a DHCPv6 client.
Describes how to set up administrator and non-administrator accounts for access.
Details how to configure general SNMP settings, including version and community values.
Describes creating SNMP users for authentication using SNMP v3.
Configures system logging settings and a list of external syslog servers.
Describes how to view or define a schedule on the Switch.
Details how to configure Green Ethernet settings for power saving.
Configures static link aggregation settings for ports.
Enables Link Aggregation Control Protocol (LACP) for dynamic aggregation.
Configures global LLDP settings on the Switch.
Configures LLDP-MED parameters for media endpoint devices.
Configures LLDP-MED network policy parameters.
Configures LLDP-MED location parameters for endpoint devices.
Displays PoE status, power usage, and allocation for PoE models.
Sets PoE power management mode, priority levels, and power-up settings.
Applies schedules to ports to control PoE power availability.
Configures Switch port settings such as speed, duplex, and flow control.
Describes how to enable and configure the Loop Guard feature on the Switch.
Selects a monitor port and specifies traffic flow to be copied.
Describes IGMP snooping for efficient multicast traffic forwarding.
Enables IGMP snooping on VLANs for multicast group management.
Configures static multicast MAC addresses for ports to receive multicast streams.
Activates DiffServ to apply marking rules or IEEE 802.1p priority mapping.
Configures DSCP to 802.1p mapping for traffic prioritization.
Sets priorities for the Switch's queues to distribute bandwidth.
Assigns priority levels to each physical queue on the Switch.
Configures bandwidth control to limit traffic going through the Switch.
Activates STP modes like RSTP or MSTP on the Switch.
Configures the settings for Rapid Spanning Tree Protocol (RSTP).
Configures Multiple Spanning Tree Protocol (MSTP) settings.
Configures MSTP port settings for participation in MST instances.
Views and configures rules for traffic filtering based on MAC addresses.
Configures static MAC address forwarding rules for ports.
Configures a static VLAN for the Switch.
Configures static VLAN (IEEE 802.1Q) settings on a port.
Allocates a VLAN for voice traffic with defined priority for quality preservation.
Assigns incoming packets to VLANs based on source MAC address.
Assigns packets to VLANs based on vendor ID and MAC address.
Defines forwarding decisions based on destination MAC address and associated port.
Configures port-based VLAN settings, including connectivity and isolation.
Configures the ARP learning mode for each port on the Switch.
Views and configures static ARP entries that do not age out.
Configures DHCP relay for clients not in the same broadcast domain.
Views and configures DHCPv4 option 82 profiles.
Configures global DHCPv4 relay settings.
Configures DHCP settings based on the VLAN domain of DHCP clients.
Enables and configures the DHCPv6 relay agent for IPv6 clients.
Configures and enables static routes for IPv4 traffic.
Configures and enables static routes for IPv6 traffic.
Configures the RADIUS server settings for authentication and accounting.
Configures authentication, authorization, and accounting methods.
Decides which services may be used to access the Switch.
